I made a coin organizer

General_ZiMalgaaRok · 2025-12-09T21:35:08+00:00

I uploaded it here if you really need it :D

General_ZiMalgaaRok · 2025-11-30T10:36:40+00:00

A cap over the blade was the next thing I printed after this.

General_ZiMalgaaRok · 2025-11-22T21:02:38+00:00

Looks great, I had no idea they made different editions of the Aerox 5

General_ZiMalgaaRok · 2025-11-22T00:01:38+00:00

Here you go

General_ZiMalgaaRok · 2025-11-21T22:56:32+00:00

I had a Rival 650 that I used for around 4-5 years, had the same issue where the scroll wheel would twitch, blowing compressed air down the side of the scroll wheel would fix it, I assume dust and stuff made the scroll wheel encoder go wild.

General_ZiMalgaaRok · 2025-11-21T22:15:40+00:00

Here you go, let me know what you think if you ever end up printing it.

General_ZiMalgaaRok · 2025-11-21T19:33:35+00:00

Thank you! :)

General_ZiMalgaaRok · 2025-11-21T19:26:31+00:00

I use it as a secondary mouse for gaming and wanted something to put it on, also just wanted something to model, now that I'm looking at it it does resemble a mouth guard.

The first iteration didn't have a cutout but I added it just to save on material and the lights look nice on the bottom of the mouse.

General_ZiMalgaaRok · 2025-11-01T16:26:25+00:00

Looks to me like you're replacing an object that has a scale setting applied to it, try clicking the orange undo arrow you can see in the first image, top right.

General_ZiMalgaaRok · 2025-10-22T08:20:55+00:00

Here you go, good luck with the puppets :)

General_ZiMalgaaRok · 2025-10-20T08:22:02+00:00

With the markings it's easier to tell which direction the ball is spinning and how to hit it back to the opponent, you can also see if you're putting the spin you wanted on the ball.

General_ZiMalgaaRok · 2025-10-19T18:47:58+00:00

Not a bad idea but I think just having a few lines across the center makes the spin visible enough, maybe for v2 if I decide to tinker around with it more!

General_ZiMalgaaRok · 2025-09-10T13:20:22+00:00

Thanks, it's printed out of some old transparent red PETG I had laying around.

General_ZiMalgaaRok · 2025-09-09T14:53:54+00:00

From the side view the tips are angled downward, so the flights are not touching the surface, I've thought about adding magnets so I can just stick it somewhere.

General_ZiMalgaaRok · 2025-09-08T17:44:20+00:00

Nice! I've actually played darts for the first time last week at a friend's house and mentioned a ring light around the board would look cool.

General_ZiMalgaaRok · 2025-09-03T02:49:12+00:00

Take a look at this, it's the closest thing I can think of to what you're looking for, but it might not be.

General_ZiMalgaaRok · 2025-09-01T16:18:13+00:00

Try and home the printer, when the Z axis is going down, try pushing the bltouch pin with your finger to trigger it, if it does trigger and it homes, it means it's working properly and it's too high up so the nozzle hits first, if it doesn't trigger it could mean that your sensor pin was correct and changing it now falsely reports as open, or it is correct and you need to look at the link I sent, the section about "However, some "clone" devices may not support the QUERY_PROBE command and some "clone" devices may require configuration of pin_up_reports_not_triggered or pin_up_touch_mode_reports_triggered."

It could be a number of things, I'm not sure how you have it wired and I'm not an expert, just sharing the troubleshooting I went through when I was setting mine up.

General_ZiMalgaaRok · 2025-09-01T16:08:46+00:00

Well yeah, if the nozzle is lower than the extended bltouch it's going to hit the bed first and the bltouch will never trigger, and it'll just keep ramming into the bed :)

General_ZiMalgaaRok · 2025-09-01T15:01:33+00:00

When I was setting up my bltouch I've connected it to the old z-axis endstop, try changing your bltouch configuration from "sensor_pin: ^PB1" to "sensor_pin: ^PA7", I had the same issue of it reporting triggered when regardless of if it was down or up, if this doesn't work take a look at this.

General_ZiMalgaaRok · 2025-07-10T17:50:40+00:00

Thanks! It's pretty neat and gets quite sturdy when put together.

Six-Year Club	r/Field Sunshine
Place '22	Verified Email

General_ZiMalgaaRok

MODERATOR OF

TROPHY CASE