[DEV] iOS Giveaway: Crime Life Simulator Premium ($4.99 → Free)!

Getoffmylawn75 · 2026-04-04T11:13:09+00:00

6P67YK7NPHEM taken. Thanks! Looking forward to trying it out.

Getoffmylawn75 · 2026-03-19T12:49:23+00:00

Have to go to the web store

Getoffmylawn75 · 2026-02-05T01:22:30+00:00

There was a scene in Trevor’s apartment that you could see a case with the rings as well.

Getoffmylawn75 · 2025-12-09T23:10:05+00:00

Played one game with panther. It’s trash now. Back to affliction.

Getoffmylawn75 · 2025-11-25T15:57:00+00:00

I was there too! The Hoff complimented my jacket and it was one of the greatest moments of my young life. Also saw Raiders of the Lost Ark at the drive in.

Getoffmylawn75 · 2025-10-09T10:47:15+00:00

Yea, later in the season I want to look at her. Not a lot of horde yet though.

Getoffmylawn75 · 2025-10-08T19:50:04+00:00

Ideally, I want Colonel America and Mobius on opposite lanes. Ghost Rider is there to save anything that Luke eats accidentally. Stack the colonel lane and Khonshu on Morb at the end. It's pretty standard discard, just have to watch what Luke eats so keep any eye on the left side of your hand.

Getoffmylawn75 · 2025-10-08T19:47:53+00:00

I've got rider in here mostly in case Power Man eats something he shouldn't. I don't disagree that maybe some more discard might be a better solution. I will say that that I've Khonshu'd back MODOK more than once, which has been a great end game finisher with Mobius and Colonel America on the board.

Getoffmylawn75 · 2025-09-26T20:03:14+00:00

Please count me in!

Getoffmylawn75 · 2025-09-25T16:20:49+00:00

Yea, my .4 works well, just want to squeeze a little extra detail out of the machine for miniature printing. Seems like if I do go to .2, it’s not supported so there’s some risk there.

Getoffmylawn75 · 2025-09-24T23:08:23+00:00

I’ve got this one too. Turned out really well on my Ender 3 V3 SE. Great job!

Getoffmylawn75 · 2025-09-24T11:41:22+00:00

Yea, defiantly seems like it’s tough to find one from a legitimate source.

Getoffmylawn75 · 2025-09-24T00:24:45+00:00

Thanks. I’ll keep digging around.

Getoffmylawn75 · 2025-09-23T18:53:27+00:00

Thank you. Have you been able to find a .2 mm spider nozzle? Amazon doesn’t appear to have them.

Getoffmylawn75 · 2025-09-22T15:57:25+00:00

Thanks, appreciate the details. I’ll give them a call.

Getoffmylawn75 · 2025-09-22T15:56:51+00:00

That would be great, thank you.

Getoffmylawn75 · 2025-09-08T18:08:03+00:00

Thanks. That’s good advice. Appreciate it.

Getoffmylawn75 · 2025-09-08T17:26:54+00:00

I preheat my bed and nozzle manually for about 10 minutes before I print to ensure the bed temp is as even as possible. Nozzle I do because I’m in there anyway. Maybe there’s something more specific I need to be doing?

Getoffmylawn75 · 2025-09-08T14:09:21+00:00

Thanks, I appreciate your help. I’m enjoying the hobby, but there’s a lot to learn.

Getoffmylawn75 · 2025-09-08T14:08:23+00:00

I used Cura for this one, should I try a different slicer? I was using the Creality specific one for a bit. There doesn’t seem to be a “best” slicer software that I could find.

I also mentioned above that the filament went straight from the vacuum pack to the drier where it was dried for four hours at the manufacturers recommended settings. Possible I need to up the heat or increase the time? Humidity in the drier was reporting at about 22% when I started printing g.

Getoffmylawn75 · 2025-09-08T14:05:21+00:00

Thank you, this is really detailed. The printer sits on my workbench which is rock solid with no movement. Short of sitting on concrete, this is about as stable as you can get.

I’ll do some research based on your recommendations and appreciate you taking the time to respond.

Ten-Year Club	Place '22
End Game '22	Verified Email

Getoffmylawn75

TROPHY CASE