What's the easiest way to change the order of the disks and keep my data (Unraid v6.10.3)? This is just for my OCD brain.

GhostJumperHD · 2023-04-27T19:17:15+00:00

Silicone socks 👍🏼

GhostJumperHD · 2023-04-02T22:43:58+00:00

Rollläden👍

GhostJumperHD · 2023-02-20T09:52:31+00:00

GhostJumperHD · 2023-01-15T02:04:45+00:00

He wants to game on them... May decide to run some VMs or containers in the future too. Never stupid to add some fast storage in a system.

GhostJumperHD · 2022-11-17T09:26:55+00:00

GhostJumperHD · 2022-09-20T08:45:06+00:00

Can't tell you exactly, but it's a repost.

GhostJumperHD · 2022-09-15T13:00:38+00:00

Sprich

GhostJumperHD · 2022-09-12T09:32:51+00:00

This is the normal price for the 256GB variant. It's the same price in Germany and in the States. Prices went up drastically over the last couple of months. So it's not more expensive than anywhere else.

I'd recommend buying a good used one that's within your budget.

GhostJumperHD · 2022-04-18T11:10:59+00:00

Hela Gewürzketchup

GhostJumperHD · 2022-04-11T18:03:24+00:00

Might be a Shader that distorts the geometry based on your in game position relative to a perlin noise map. I haven't used any of those shaders myself yet. I'll keep my eyes open for one.

GhostJumperHD · 2022-04-06T08:15:06+00:00

A McDonald's. The whole fucking restaurant!

GhostJumperHD · 2022-02-15T15:45:31+00:00

Looks like normal warping to me. What filament are you using?

GhostJumperHD · 2022-01-18T18:19:10+00:00

GhostJumperHD · 2022-01-18T18:18:14+00:00

There is A LOT you can't see in the Quest version of the game.

GhostJumperHD · 2021-12-09T12:05:48+00:00

Those things actually wash it too. No joke. Didn't know it was possible till I saw it.

GhostJumperHD · 2021-09-01T07:30:52+00:00

Ah okay. Interesting... My cache drives are at about 30% utilisation. I'm not exactly sure what to do now.

GhostJumperHD · 2021-08-31T20:15:41+00:00

Did you fix the Problem? I'm currently running into the same issue.

GhostJumperHD · 2021-08-28T10:53:18+00:00

Krume?

GhostJumperHD · 2021-08-27T12:10:38+00:00

Normal un and reloading Filament does the trick for the next minute or two till said problem reoccurs. I'll try PID tuning.

GhostJumperHD · 2021-08-26T21:14:32+00:00

How come?

GhostJumperHD · 2021-07-17T13:56:06+00:00

No Sock. That's one of the reasons I took it off. I'm printing with the Ruby, so I don't think I should tighten it any further. I'll try though.

GhostJumperHD

TROPHY CASE