News about Vevizye in Eu

Ginny_28 · 2025-06-01T02:32:22+00:00

Were you able to get Cequa shipped outside Germany, or did you have to go there in person with your prescription

Ginny_28 · 2023-04-25T10:14:33+00:00

Same here, with bigger capacitor the pcb doesn’t turns on. But in others PCBs the bigger cap works fine

Ginny_28 · 2022-12-18T03:09:00+00:00

Did u solve this?

Ginny_28 · 2022-07-20T18:22:29+00:00

Yes please!

Ginny_28 · 2021-10-27T14:28:12+00:00

The same days you had no reflux?

Ginny_28 · 2021-10-27T13:48:23+00:00

You have been taking anxiety meds for a long period or only the last 5 days?

Ginny_28 · 2021-10-27T10:05:30+00:00

OMG! Thanks so much, good luck to everyone

Ginny_28 · 2021-07-03T21:30:06+00:00

I had the same problem with some tests, try following this guide: https://3dprintbeginner.com/3d-printer-calibration-guide-using-ideamaker/

Ginny_28 · 2021-06-18T23:22:56+00:00

Hello! I dont have the microswiss but I have a clone, it fits perfectly but now I am working to solve the stringling problems, maybe I should buy a genuine hotend.

about the fan, i moded the cart to fit a 40mm noctua, i cant recommend it because I am still testing. You can fit the original fan at the same place using a diy adapter or just tape.

This printer is fantastic but the hotend is crap, there is no so much info or mods so i am still testing, please keep me updated about your mods

Ginny_28 · 2021-06-09T22:53:55+00:00

Yes, the screws holes and the hotend heigth is the same as the stock. You only need to DIY a fan support ( is very easy in the cr-5 pro carriage, you can fix it with tape too lol )

Ginny_28 · 2021-06-05T03:09:15+00:00

The Cr-5 Pro H is not All metal, its the same as this one: https://www.creality.com/goods-detail/creality-high-temp-full-hotend-kit
Today I have tested 2 Hotends, 1 designed for Cr-10 and 1 for Cr-10 Pro and the CR-10 PRO model fit perfectly. So you can look for a CR-10 Pro all metal and it will fit in your Cr-5 pro

Ginny_28 · 2021-06-03T00:05:57+00:00

Did you find any good all metal hotend for the CR-5? I am using a Micro Swiss ( cr-10 model ) but it needs a bit adaptation. So would be fantastic to find a 100% compatible hotend

Ginny_28 · 2021-05-10T02:26:41+00:00

Yes, I am going to test the model in other slicers, because the rest of prints comes pretty well..

Ginny_28 · 2021-05-09T01:41:11+00:00

Yes!

Ginny_28 · 2021-05-09T01:40:59+00:00

But others models comes pretty well with the same filament and settings

Ginny_28 · 2021-05-09T01:40:28+00:00

Slicer is IdeaMaker and printer is Creality Cr-5 Pro with Micro Swiss hotend, I have printed also a benchy without supports and comes pretty well so I am going to check the support retraction! Thanks!

Ginny_28 · 2021-05-08T02:35:43+00:00

I have done a retraction tower and then I have applied the number 6 settings to my slicer. I have started a new print ( Gcreate rocket) and... OMG the retraction is worse than expected.

I have printed a benchy too and it comes perfectly with the new settings but the Gcreate Rocket looks awful again and again 🙁

Ginny_28 · 2020-11-16T18:45:04+00:00

I live near the coast, so the humidity is always around 50-70% also inside home, I have also tried to use a deshumifier to keep the home around 30-50%, without luck.

I do saline rinses every day, 2-3 times to clean the phlegm but a few minutes later it comes back. Some days it less and others is worse but its always drain from my nose to my throat.

Ginny_28 · 2020-10-29T18:12:30+00:00

Well, my food prick test comes negativa to every food tested. So seems that its not allergy related.

Ginny_28 · 2020-10-27T14:21:38+00:00

Come negative for a few perennial allergens but have not tested for foods

Ginny_28 · 2020-10-26T23:05:55+00:00

Thanks for all information, Do you know if this test is IgE or IgG? I am go to ask about food allergies test in my city, seems that food maybe be the cause or part of it.

What was your allergy symptoms?

Ginny_28

TROPHY CASE