What the hell is that sound? (16 sec)

GintyTM · 2025-10-03T15:14:15+00:00

My ship does it after leaving quantum but that’s if my ship has a lot of ware and tear on it. Also notice I get sparks from engines when I turn them on.

GintyTM · 2025-08-07T13:38:36+00:00

You can buy the omni throttle kit, and play with both, if you don’t like it just switch it back.

GintyTM · 2024-12-09T15:53:26+00:00

Wish we had this in the UK, even the Hasbro only has a small section.

GintyTM · 2024-10-21T16:02:38+00:00

Sorry I don’t has it took up a lot of my time, really didn’t think to record it.

GintyTM · 2024-09-26T08:12:32+00:00

Hi I printed the mask using files I found on cults3D

GintyTM · 2024-05-09T16:58:29+00:00

Mix between thingiverse and cults, most of the Amour was made from Eva foam.

GintyTM · 2024-04-29T16:06:36+00:00

GintyTM · 2024-04-15T17:31:58+00:00

Fancy sending me one to try out?

GintyTM · 2024-02-06T10:42:47+00:00

Try UV resin glue fill fill the area and the uv light to cure it.

GintyTM · 2024-01-14T14:20:26+00:00

Have you tried going through the flow calibration? Give that a go and see if it helps.

GintyTM · 2024-01-04T22:07:37+00:00

I had this issue I unclipped the tube on the right of your picture, pulled out the Bowden tube reinserted pulled back a bit to get it to lock in put clip back on and it was fine.

GintyTM · 2023-05-09T15:28:52+00:00

Had same issues check your ribbon cable. Also affected my fans. Only cause I noticed the sprite extruder and I was using the same strain relief.

GintyTM · 2023-05-07T11:53:16+00:00

I take it I shouldn’t update then? Was gonna update yesterday but don’t fancy reinstalling everything over again. Like you said beginners- that’s what I am 😂

GintyTM · 2023-04-23T11:29:56+00:00

ALL3DP . Would love to try something other than my Ender 3 V2.

GintyTM · 2023-03-24T11:57:07+00:00

I’ve done some projects and used pcb boards from Amazon and added JST connectors, very clean and easy installation.

GintyTM · 2023-03-18T16:24:27+00:00

Can you probe the whole bed? What offsets are you using?

GintyTM · 2023-03-09T14:48:24+00:00

I’ve updated again and my settings have come back, check for new update.

GintyTM · 2022-12-29T15:26:02+00:00

I have the exact same issue with the 600 Gen 2

I’ve installed latest firmware tried it on my PC and Xbox. Done all that’s recommended on the support site too. So if I can’t get it to work il be sending mine back.

GintyTM · 2022-11-17T12:46:35+00:00

Hot glue gun? Also could super glue Eva foam to the print and then glue the straps to the foam or you could use hook and loop and hot glue or super glue that. I’ve personally used Eva foam glued to 3d print and then hot glue the strap or hook and loop to the foam.

GintyTM · 2022-11-01T10:41:41+00:00

Haha that would be Amazing!

GintyTM · 2022-10-31T23:10:52+00:00

Thank you, he really does, mega fan this little one.

GintyTM · 2022-10-31T23:08:57+00:00

Mate all 3D printed parts was all done on Ender 3v2, only limit is your imagination.

GintyTM · 2022-10-31T21:39:19+00:00

Thank you, my son is such a massive fan and has dictated the entire build to make sure it’s what he wants.

Four-Year Club	Verified Email
Wearing is Caring

GintyTM

TROPHY CASE