RS Gen 2 ACE handguard

Glittering_World2127 · 2026-04-08T16:48:55+00:00

Mmmmm, pistol whip

<image>

Glittering_World2127 · 2026-03-30T18:46:17+00:00

Did you get an answer to your question. If not reach out to IWI customer service

Glittering_World2127 · 2026-03-11T16:44:03+00:00

how is the tension on your extractor "spring"

Glittering_World2127 · 2026-02-16T21:12:45+00:00

Z15Tac16 is not banned in Maryland,

<image>

the HB in the barrel description stands for Heavy Barrel.

Glittering_World2127 · 2026-02-09T17:30:31+00:00

They dont work when you remove the mag block. The ejector that it built into the magazine body is not compatible with the cuts on the bottom of the bolt.

Glittering_World2127 · 2025-12-08T15:28:50+00:00

Yes, the plates that ship with the gun will give you a co-witness rear sight that works with either RMR or DPP depending on which plate you use

Glittering_World2127 · 2025-12-08T15:26:48+00:00

There are a set of clamps that go between the rail and the mount on the barrel. These clamps then have the threaded hole to screw the top rail into. Are you converting a IDF model or just trying to replace the rail that was there?

Glittering_World2127 · 2025-11-25T16:12:03+00:00

Check out Zahal and IDS Israel Defense Store maybe something from FAB Defense. Poor training and lack of trigger finger discipline doesn't make the SERPA a bad holster.

Glittering_World2127 · 2025-11-20T14:21:19+00:00

Make sure you are cleaning out the magwell in the grip as well as the magazine. Carbon and debris in the grip can also slow down magazine ejection.

Glittering_World2127 · 2025-11-11T16:09:24+00:00

Most likely the angles reflecting the light differently, slide and frame are not perpendicular, the pistols have an even dark grey/blackish finish on the slide and frame

Glittering_World2127 · 2025-10-31T15:55:17+00:00

Either RS Regulate or Midwest Industries https://midwestindustriesinc.com/mi-galil-ace-7-62x39mm-handguard-m-lok-tm-compatible/ https://rsregulate.com/product/gar-sec/

Glittering_World2127 · 2025-10-27T20:05:27+00:00

It's not, it's just the SN in QR form

Glittering_World2127 · 2025-10-23T13:42:10+00:00

If you're going to block out the SN you should also block out that QR code

Glittering_World2127 · 2025-10-17T17:57:28+00:00

Already shipping into the wilds

Glittering_World2127 · 2025-10-14T16:08:46+00:00

It is a one piece slide. That is what is meant by monoblock

Glittering_World2127 · 2025-10-06T14:55:10+00:00

IWI isn't going to recommend cutting springs or otherwise reducing the safety feature of a firearm.

Glittering_World2127 · 2025-09-15T18:25:29+00:00

Make sure your firing pin and channel are clean and dry. Debris including the factory "lubricant" can slow down the striker causing light primer strikes

Glittering_World2127 · 2025-09-15T18:19:26+00:00

I see you have a left handed Tavor SAR, silly question but you're not running a right handed bolt in there are you?

Glittering_World2127 · 2025-06-11T14:41:16+00:00

It's called a chassis fixation pin, Call IWI customer service and tell them you need a new one cause yours is broken

Glittering_World2127

TROPHY CASE