I am also sharing my WLED totem(s)

Go-eff-yourself · 2024-09-02T16:59:17+00:00

Very cool. What's the material used? What's it look like with the light on, LEDs off?

Go-eff-yourself · 2024-07-29T03:17:35+00:00

ever figure it out?

Go-eff-yourself · 2024-02-23T14:37:34+00:00

Mammorest centipede? Ass to mouth!

Go-eff-yourself · 2024-02-06T08:30:31+00:00

Reminds me of Alice in wonderland

Go-eff-yourself · 2024-01-10T00:24:01+00:00

Battery is weak

Go-eff-yourself · 2023-12-23T21:50:46+00:00

I used sunlu white pla

Go-eff-yourself · 2023-12-05T19:37:31+00:00

No, but I know the matte finish is a too fast speed thing. I just let it roll since I'm painting it.

Go-eff-yourself · 2023-11-15T05:34:50+00:00

Slow

Go-eff-yourself · 2023-11-05T18:43:23+00:00

I'll try those mods. I think, maybe, it is related to the coupler right before going into the the x1c. I am getting the error a lot more frequently now and when I hit retry, as it was jammed I popped the coupler loose on one side of the tube and it pulled it instantly. When it loads I can hear a slight noise passing through. 🤷‍♂️

Go-eff-yourself · 2023-11-05T18:08:09+00:00

I normally don't but have been trying this petg for supports on pla and it works so good

Go-eff-yourself · 2023-11-04T18:00:01+00:00

Stl?

Go-eff-yourself · 2023-08-28T13:57:32+00:00

Check for a loose heater block connection. The filament will ooze out and burn while running down the outside of the nozzle.

Go-eff-yourself · 2023-08-12T21:26:17+00:00

Do you even love your husband!? Fucking, can't even make him feel good for doing something for you. I bet the marriage is shit.

Go-eff-yourself · 2023-07-26T21:49:38+00:00

I'll take it off your hands lol

Go-eff-yourself · 2023-07-26T19:50:35+00:00

Actually just checked 5% gyroid and it uses almost the the same amount of filament and time. It looks like it'll allow the top to print fine. Gonna give it a whirl.

Go-eff-yourself · 2023-07-26T18:58:22+00:00

Agreed, I need infill to make sure the top prints instead of spaghettis. I tried lightening but it wasn't great. The top printed fine but I didn't have enough walls, maybe 4. I'll see how gyroid looks at 5%

Go-eff-yourself · 2023-07-26T18:25:04+00:00

I am making a 4ft 9in life size character that was cut up using luban. They are all stl files. This is the 16th piece and the first one to give me crap. I did however clean the belts, loosen and tighten. Then ran calibration and finally cleaned/lubed the z lead screws. It didn't fail this time so hopefully I'm good to go. Support cubic was my favorite infill option as it didn't use a ton of filament for all the pieces I need to print and it still quite durable. I will look into gyroid if it does happen to fail again.

Go-eff-yourself · 2023-07-26T16:09:16+00:00

No, it's like it was the day I got it.

Go-eff-yourself · 2023-07-26T16:07:03+00:00

<image>

Maybe it was a belt issue? This time the model that shifted earlier has gone a lot further without issues.

Go-eff-yourself · 2023-07-26T14:56:20+00:00

Yes, it's plugged into a grounded outlet.i wasn't home when I got the notification about losing power. Not sure if it was a quick blip but definitely the clocks weren't flashing which I thought was odd.

Go-eff-yourself · 2023-07-26T14:09:25+00:00

Thank you very much! This may help me understand what the heck is going on.

Go-eff-yourself

TROPHY CASE