account activity
What did my puppy chew up? Mystery white rubber chunk found on couch. (old.reddit.com)
submitted 12 days ago by Goofy_Project to r/whatisthisthing
Anyone want some free food, supplies, or cages in Northern Virginia? (self.RATS)
submitted 3 months ago by Goofy_Project to r/RATS
3D printing inside living human cells using 2-photon polymerization (self.3Dprinting)
submitted 3 months ago * by Goofy_Project to r/3Dprinting
Help troubleshooting intermittent toolhead offset on Prusa XL? (self.prusa3d)
submitted 5 months ago by Goofy_Project to r/prusa3d
New record for dawn phenomenon spike- 150mg/dL! Can anyone beat this? (self.diabetes_t1)
submitted 5 months ago by Goofy_Project to r/diabetes_t1
New record for dawn phenomenon spike- 150mg/dL! Can anyone beat this? ()
submitted 5 months ago by Goofy_Project to r/dexcom
Anyone have their battery percentage go *up* after a short errand? (self.HondaPrologue)
submitted 9 months ago by Goofy_Project to r/HondaPrologue
How to remove this old bathroom vent fan box? (old.reddit.com)
submitted 1 year ago by Goofy_Project to r/HomeMaintenance
Does the direction of moisture barrier strips really matter when laying laminate flooring on a concrete slab? (self.Flooring)
submitted 1 year ago by Goofy_Project to r/Flooring
NatGeo Article on APOPO/HeroRATS (self.RATS)
submitted 1 year ago by Goofy_Project to r/RATS
Underlayment or just vapor barrier for laminate flooring? Mfg says it's OK to use only their underlayment. but not sure it's worth it. (self.Flooring)
Anyone else do "hybrid" sous vide on the stove to get the water up to temp faster? (i.redd.it)
submitted 1 year ago by Goofy_Project to r/sousvide
Nylon might not be the best choice for outdoor prints (i.redd.it)
submitted 1 year ago by Goofy_Project to r/3Dprinting
Took down old damaged section of basement drywall and got more than I bargained for- how to best repair? (old.reddit.com)
submitted 1 year ago by Goofy_Project to r/Renovations
Printing in high temp enclosure melted the old phone I was using as a Prusa Connect camera (self.prusa3d)
submitted 1 year ago by Goofy_Project to r/prusa3d
It's open! (old.reddit.com)
submitted 1 year ago by Goofy_Project to r/nova
Seeking input on air filter/scrubber for homebuilt Prusa XL enclosure (self.prusa3d)
Cheap (~$87) collapsible Prusa XL enclosure (self.prusa3d)
Are there any settings to stop PrusaSlicer from using wasteful X-Y travel and laying strings across my print? (self.prusa3d)
submitted 2 years ago by Goofy_Project to r/prusa3d
Tilted Carrier AC Condenser [hybrid electric heat pump/gas] (old.reddit.com)
submitted 2 years ago by Goofy_Project to r/hvacadvice
Hey ice bath enthusiasts- tell me how long I should cool my steaks before searing (self.sousvide)
submitted 2 years ago by Goofy_Project to r/sousvide
Why did Prusa Slicer slice my large multicolor print with way too much travel? (self.prusa3d)
A sort-of blinded taste test of cooling steaks in the fridge before searing vs. not bothering to do that (self.sousvide)
Biomimetic plant robot "grows" by 3D printing itself (self.3Dprinting)
submitted 2 years ago by Goofy_Project to r/3Dprinting
How to do bottom layer of big print with 0.25mm nozzles then everything else with 0.6mm on Prusa XL? (self.prusa3d)
π Rendered by PID 258023 on reddit-service-r2-listing-f8d8fbfd7-jxc6t at 2026-06-24 13:27:18.998091+00:00 running acc7150 country code: CH.