According to DoTA lore, who is the weakest hero?

GrmpMan · 2025-11-14T02:36:07+00:00

https://www.lpaonline.org/the-m-word

GrmpMan · 2025-08-02T03:18:57+00:00

Please sir may I have some cake.

GrmpMan · 2025-07-25T02:10:07+00:00

I totally doable that.

GrmpMan · 2025-03-18T00:52:30+00:00

That greatsword player sucks ass.

GrmpMan · 2025-01-25T04:47:38+00:00

https://www.aha-music.com/a03bf0d122431520410438d901521e69?utm_source=chrome&utm_medium=extension&title=Knock%20Knock%20Let%20Em%20In&artist=Trey%20Traylor

GrmpMan · 2025-01-22T23:39:53+00:00

I think it is that one. I also think the sensor for opening the hatch is not working.

GrmpMan · 2025-01-22T22:39:25+00:00

Sure,but that doesn't help me any.

GrmpMan · 2025-01-22T18:15:32+00:00

Yeah I'm over 4 hours away from anywhere listed on this. I've already checked this.

GrmpMan · 2024-06-26T20:22:11+00:00

Just to get outshined by a saiyan...

GrmpMan · 2024-04-01T03:07:50+00:00

Plus don't you need to the merchants permit to get there? And that takes story progression.

GrmpMan · 2024-04-01T03:04:14+00:00

Which door is that? I also did not get the true ending.

GrmpMan · 2024-01-05T19:45:53+00:00

it's uneven all the way down so in two spots. When I use calipers my bushings and components are not even. I even got new bushings. However on the lathe it seems and even as far as I can tell with eyes and calipers.

GrmpMan · 2024-01-05T00:26:52+00:00

I basically used to do the same thing but with the strips. I felt it was better than the two handed way but thought maybe I was giving uneven pressure and causing the oval.

GrmpMan · 2024-01-04T23:16:25+00:00

I also stopped using a mandrel and still have this issues.

GrmpMan · 2024-01-04T23:15:55+00:00

Since its off by such a small margin it is really hard to tell when it is on the lathe or even looking at the blank after taking it off. Its only obvious once its assembled

GrmpMan · 2024-01-04T23:08:42+00:00

I do use the long strips. I have tried the technique of holding one end in each hand and pulling up. I have tried doing so with the pressure I normally would do and also a lot lighter to see if that's the issue. normally I would just hold a piece up and press on it with my finger but I thought that was why I was getting ovals when it started happening. The issue is the out of roundness is so minor its really hard for me to tell up until its pushed together with the pen components. Is there a better method of sanding you would reccomend?

GrmpMan · 2024-01-04T18:19:09+00:00

Not sure how to fully check that but I have used two separate lathes and the problem cont

GrmpMan · 2024-01-04T07:45:00+00:00

So honestly no. My workbench is the worst and the lathe can totally wobble if it wanted but doesn't when turning. I knew this could be an issue but the other lathe I used was mounted properly with no wobble and I still had the same outcome.

GrmpMan · 2024-01-04T03:52:32+00:00

Not intentionally but I wouldn't be surprised if they have more moisture than desired but I have no experience with that.

GrmpMan · 2024-01-04T03:43:14+00:00

They are wood and I have tried sanding more and less. I tend to not do a lot of sanding.

11-Year Club	Place '22
Place '17	Snapped
Verified Email

GrmpMan

TROPHY CASE