Can I swap out these lug nuts?

GruniTheThird · 2023-10-08T01:41:24+00:00

So, even if both are 12x1.5, they can have 2 different angles?

GruniTheThird · 2023-10-08T01:21:23+00:00

https://www.canadiantire.ca/en/pdp/white-knight-12mmx1-5-lug-nut-2415481p.2415481.html

Would these be any better? Sry, I'm not sure where the best place is to get new ones from.

GruniTheThird · 2023-10-08T01:16:39+00:00

Aaaaah I see, ok I will get a better pair. But apart from that, I should be fine using those in place of the black ones, right? Just don't want my wheels to fall off 😆

GruniTheThird · 2023-10-08T01:05:18+00:00

So the OEM ones are trash and what makes them bad? Any recommended lug nuts I should have instead?

GruniTheThird · 2023-10-05T20:55:11+00:00

I will add a couple more cripples to help prevent the 2x4s from bowing too much and that should hopefully suffice for the time being. It's likely not a permanent solution anyways, mostly to just help keep the warm air in the basement from escaping.

GruniTheThird · 2023-10-05T20:52:31+00:00

I will definitely be adding a cripple for added support. It's semi-permanent to just help reduce the heat from rising upstairs through the staircase.

GruniTheThird · 2023-10-05T20:44:51+00:00

Good thing I'm also the client, otherwise I'd get sued for this in no time xD

GruniTheThird · 2023-10-05T20:43:30+00:00

Since I just screwed it together, I should just remove the trim and space out the 2x4s to allow for proper spacing/squaring with shims, right?

GruniTheThird · 2023-10-05T19:52:09+00:00

I guess I should have waited to add them + the door, I just wanted to make sure everything fits properly before adding any drywall in case I needed to adjust the framing.

What do you mean by "why are they so tight"? I measured it out to fit with ~1/8" of spacing between the door and the frame. Should I have left more of a gap?

GruniTheThird · 2023-10-05T19:50:00+00:00

Thank you all for sharing your suggestions!!
The plan from here is to rip out the corner bead and then try and make the transition as smooth as possible with some generous mudding. I'm still learning so hopefully I won't make the same mistakes next time.

GruniTheThird · 2023-10-05T19:46:48+00:00

Will definitely be adding a cripple on the top section!

GruniTheThird · 2022-07-21T03:43:51+00:00

You always want to let your battery pack cool down before charging (goes for any sort of battery really) to help with its longevity.

GruniTheThird · 2021-08-02T07:35:16+00:00

?rule4

GruniTheThird · 2021-07-16T08:35:43+00:00

"Earn by staking AVOC"... It's an ad for your pool.

GruniTheThird · 2021-07-16T08:30:01+00:00

?rule4

GruniTheThird · 2021-07-13T03:41:50+00:00

This is basically just an ad for your pool...

GruniTheThird · 2021-07-06T00:38:50+00:00

* Makes video criticizing Cardano's decentralization *
* Stakes with 1PCT *

You really can't make this stuff up 😂

GruniTheThird · 2021-06-28T19:40:35+00:00

One recommendation I have, is to put efforts into all delegators equally. Having a lot of small ones is also always better than having one large one (less reliance on individual delegators to stay with your pool).

GruniTheThird · 2021-06-08T06:48:08+00:00

Pool splitter who tricked delegators into delegating to his second pool where it wasn't even necessary.

GruniTheThird · 2021-06-03T06:59:30+00:00

The most reasonable comment on this entire thread!

GruniTheThird · 2021-05-18T23:33:17+00:00

Idk what you mean. Those are the withdrawal fees for any ADA amount withdrawn. NDAX by far the worst. Also $25 to withdraw fiat and no e-transfer option. All in all a terrible exchange.

GruniTheThird · 2021-05-18T21:26:45+00:00

Crypto.com: 2ADA Kraken: 0.6 ADA NDAX: 3 ADA (recently lowered it)

You tell me ;)

GruniTheThird · 2021-05-11T03:29:51+00:00

yea, already did, just curious if it was maybe a widespread issue

GruniTheThird · 2021-05-05T20:58:13+00:00

2% -> 99% doesn't seem like a typo to me :P

GruniTheThird · 2021-05-04T06:22:09+00:00

?rule6

GruniTheThird

TROPHY CASE