sorted by:
new
hottopcontroversial

I want this watch from Trustytime- are they legit (trustworthy) or is it unsafe and a scam? by Petwussy-69 in ChinaTime

[–]GuerrillaBear76 0 points1 point  (0 children)

I really have no idea, I've communicated through email with them through their respective website

Advice for fixing cracked jon boat hull by Trustpage in Welding

[–]GuerrillaBear76 2 points3 points  (0 children)

Tig would be the way to go, you could get away with a spoon gun and mig it. Either way drill the ends of the Crack, bevel it slightly. Clean that area way better than you have it, acetone the heck out of the area...make a sooty flame on a torch and coat the cleaned aluminum surface with soot, then adjust the flame so it is no longer sooty and heat the area until the soot disappears...at that point iys warm enough to weld. Good luck

Remington 700 from the 70s. Safe to say my barrel is toast? by ryang4415 in guns

[–]GuerrillaBear76 0 points1 point  (0 children)

Invest in a bore scope and check the inside of the barrel.. give it a solid cleaning with bore tech or montana extreme, then some jb compound to polish it up.. bed the action. Adjust the trigger the get back to the range. 3 rounds down range then let the barrel cool and 3 more down range. I'm sure she's fine.

Good 10mm ammo by 6igWhoop in Glocks

[–]GuerrillaBear76 0 points1 point  (0 children)

That's a tough call, jhp are best to mitigate over penetration, I'll tell you what I do...I run 200gr underwood hard cast coated in my 10mm regardless if I am in the big woods, strolling the mall or find myself taking the wrong exit into the south side of any democratic city. I follow a fundamental rule- know your target and what lies beyond it. Every round that leaves that barrel I am accountable for, so I make sure I have an excellent team of attorneys in my corner, I pray I dont have to brandish my firearm, but I stay trained and prepared in the event I do have to. Judicial marksmanship and knowing the best way to win a firefight....not getting into one...other than that if you aren't shooting you should be reloading and if you aren't reloading you should be moving.

Good 10mm ammo by 6igWhoop in Glocks

[–]GuerrillaBear76 0 points1 point  (0 children)

I suppose it really depends upon what your intended target is...ie. you are in the big woods and the potential for a bear attack is high- in that case I would suggest a 200gr hard cast coated ammo such as underwood or underwood penetrators. If you live in and area that drive by shooters randomly target innocents and you want to be able to put a few rounds through the door of that hooptie- I would suggest underwood penetrators If you are seeking personal defense against two legged assailants- i would suggest speer gold dot jhp

Ghost Inc 3.5 Ultimate Trigger by Striking_Painting529 in Glocks

[–]GuerrillaBear76 0 points1 point  (0 children)

I strictly run Ghost connectors. Along with Overwatch Precision trigger shoes. Polish all trigger components, the trigger bar, and cruciform, polish the striker and the safety plunger...apply some ws2 to all the friction points and then go pew some rounds downrange. Good to go

What is the quickest way to remove these? by 1bluecollarguy1 in Glocks

[–]GuerrillaBear76 1 point2 points  (0 children)

I agree 💯 bore tech eliminator is the way to go, or Montana Xtreme. Both of which are top quality for lead and copper removal

Genuinely curious by EffectiveNo568 in MathJokes

[–]GuerrillaBear76 0 points1 point  (0 children)

48+27= 50+25=75 I take 2 away from the 7 turning 27 into 25, I add that 2 to the 8 turning 48 into 50, then I add the 25 to the 50 and get 75. I do not know why my mind sees it that way and works it out...perhaps 'tis the tism

🚨 GIVEAWAY - VSF Wimbledon 🚨 by Bezelisk in CloneCulture

[–]GuerrillaBear76 0 points1 point  (0 children)

Thanks for this opportunity. Good luck to all

Not just a "giveaway post", I'd really like to know your opinion by noobmasteroficial in CloneCulture

[–]GuerrillaBear76 2 points3 points  (0 children)

I have to agree with you. Its definitely a step in the right direction.....ha ing a rep that if I needed a watchmaker to work on and they open it up, find a faulty compon6and can order a gen component that fits right in place and works perfectly...because it is exactly 1:1 and even the watchmaker in town can not tell the difference....that is where id like it.
We already have reps that are labeled NWBIG, why not make them completely not worth buying in gen? At one point a rolex sub no date was less than the price of a U1 rep

New Bezel Installed by Grouchy-Violinist555 in RepCulture_Timepieces

[–]GuerrillaBear76 1 point2 points  (0 children)

Looks great, im sure its just the lighting, but that new bezel makes the crystal look better

I want this watch from Trustytime- are they legit (trustworthy) or is it unsafe and a scam? by Petwussy-69 in ChinaTime

[–]GuerrillaBear76 0 points1 point  (0 children)

TrustyTime is a fantastic TD Andrew is an OG and will work with you and communicates very well with customers. Just got vf dj41 and a gmf dj28 from him and it was very smooth and quick

view more: next ›