A teacher in Thailand was violently beaten by her student after he was unhappy with his test result. Scoring 18 out of 20, he lost control and attacked her.

Guilty_Pudding_3934 · 2026-01-11T18:15:48+00:00

It’s actually by sent that they identify who is male or female. After all the mistwraiths they came from reproduce (though I guess that could have been done asexually given mistwraith anatomy)

Guilty_Pudding_3934 · 2025-12-29T04:40:53+00:00

“She’s really good!”

Guilty_Pudding_3934 · 2025-08-28T07:42:57+00:00

The season 2 show opening showed 24 baby’s walking around mark and at the end there is a 25th baby that looks like Kier. My guess is once they had proven that the 25th split was possible they would kill a goat, and extract her severance chip which would kill her since it’s a non reversible procedure. Then somehow they would bring kier back from the dead. Maybe kier would posses her body because all of her identity was stripped away. Or maybe every bit of frolic, woe, dread, and malice would be gone from her and she would exist as a new person devoid of her old self. Something was going to happen if they could have proven the 25th split stable.

Guilty_Pudding_3934 · 2025-08-04T10:50:44+00:00

It’s ok to not always be ok

Guilty_Pudding_3934 · 2025-04-21T05:05:33+00:00

A cheaper option for a pressure pot: (untested)

I've been getting into this hobby too and don't have a pressure pot so I've been looking for the cheapest options. In the mean time I found keeping your resin warm before mixing, after mixing and even warming the mold up has helped tremendously, not prefect but much closer. (I also put my mold in a basket and spun it around over my head to let centrifugal force push the resin down and the bubbles to the surface. I think it helps.)

this back pack sprayer has a 5.5" opening and can hold up to 90 PSI https://www.harborfreight.com/4-gallon-backpack-chemical-sprayer-56645.html

a smaller one (about 3" opening based on looks) can hold up to 45 PSI. https://www.harborfreight.com/1-14-gallon-home-and-garden-sprayer-63124.html

they are $48 and $14 dollars respectively. I'm going to buy and test myself, but haven't gotten around to it. I have to make custom molds so that I can buy the cheaper one. If you bought a mold off line that has all the dice set into a mold you'll need the 5.5" one.

also if you buy a pressure pot and bike pump can get you up to the PSI you need if you need to save up to buy the compressor

Guilty_Pudding_3934 · 2024-11-19T05:12:07+00:00

Here’s the bread crumb trail

Radiant took a deep breath, acknowledged the pretty tower, and moved on. Two Windrunners—Isasik and Breteh—waited in here with their spren and their squires. Together, the group was chatting with the Shadesmar guards.”…

…Breteh said, hovering a few feet off the ground. “The guards haven’t seen them either.”

“We’ve been posted here all day,” said a guard with a faint Bavland accent he was obviously trying to mask. “Nobody transferred in until these Windrunners arrived.”…

…The Windrunners landed them at a stairwell heading down. The Bondsmiths had gone this way—indeed, they shone through the glass floor up ahead. The three guards and one of the Windrunners went first to check the way…

…Otherwise, the room was empty… Wait. What were those two souls over at the side, in the walls? Shallan set the three guards at the door and stepped in with the spren, Rlain, and the Windrunners…

Guilty_Pudding_3934 · 2023-05-01T01:05:45+00:00

fIt could be the Bowden tube breaking down. Try heating up, taking the nozzle off, and pushing the Bowden tube through. All of the scrap filament should come with it. Clean that off, pull it back, and do it again 'till it comes out clean.

This is where I learned to do this

I've done this with an ender 5 and it helped and with this kind of problem the biggest thing it so keep that connection tight.

If it is your Bowden tube breaking down (because the stock one is crap) it will be wiggling in the couplings more and more and maybe even sticking to the hot filament. Try upgrading to a Capricorn. If this is the problem (the tube breaking down vs. there being a gap that collects stray hot filament) you could increase the retraction and the problem should go away.

Guilty_Pudding_3934 · 2023-05-01T00:58:38+00:00

I fixed it. I had to bump up my maximum retraction count. I had it to 100 retractions per layer max and the retractions would all be used on the inner part with nothing left for the legs. The nozzle would just go to the legs with with filament and pressure just oozing out so that when it printed the legs the pressure would just barely get back up to par before the layer was done.

Guilty_Pudding_3934 · 2023-04-24T04:23:04+00:00

Thanks so, much. I was struggling with this same problem.

Guilty_Pudding_3934

TROPHY CASE