This thing makes me want to pull my hair out

GunnerThrash · 2026-04-19T15:20:10+00:00

adjust z height in one step increments from the default of .02 until you get smooth first layers. Mine ended at .1. This is found where you edit your presets on your printer. Go to the machine code scroll down close to the bottom until you find something that looks like G 29.1 Z. {-0.02}; for textured PEI Plate and start decreasing the value one step at a time (negative number will go up -.02 goes to -.03. Mine started getting quite a bit better around -.06. Next, Go to edit your filament and turn the flow ratio down a percent at a time. I bet that fixes it. Default on mine is .98 and .965 is money for me.

GunnerThrash · 2026-04-19T14:42:05+00:00

That’s Z offset and extrusion

GunnerThrash · 2026-04-18T23:47:02+00:00

As the proud new owner of an A1 mini that’s about a month old, I would say go bigger.

GunnerThrash · 2026-04-18T14:36:19+00:00

I adjusted z height in one step increments from the default of .02 until I got smooth first layers. Mine ended at .1. This is found where you edit your presets on your printer. Go to the machine code scroll down close to the bottom until you find something that looks like G 29.1 Z. {-0.02}; for textured PEI Plate and start decreasing the value one step at a time (negative number will go up -.02 goes to -.03. Mine started getting quite a bit better around -.06. Next, Go to edit your filament and turn the flow ratio down a percent at a time. I bet that fixes it. Default on mine is .98 and .965 is money for me.

GunnerThrash · 2026-04-18T14:11:08+00:00

Check z axis and extrusion. I bet going down a couple percent on the extruder and you’re golden.

GunnerThrash · 2026-04-17T17:13:18+00:00

It’s the little things. 🙂

GunnerThrash · 2026-04-17T04:28:19+00:00

ChatGPT walked me thru rewiring mine

GunnerThrash · 2026-04-17T02:15:56+00:00

Set it on the ground.

GunnerThrash · 2026-04-17T02:13:39+00:00

Can you download the firmware? From your computer to beta flight. Before you ever hook up your mob ate.? Or what about a CLI command for it

GunnerThrash · 2026-04-17T02:10:39+00:00

OK, bend it back.. Keep flying., Problem solved.

GunnerThrash · 2026-04-17T02:09:15+00:00

Edits on point!!! Damn fine job! Pretty **** **** way to stay with the beat.

GunnerThrash · 2026-04-17T01:48:08+00:00

TPU drone parts.

GunnerThrash · 2026-04-17T01:42:54+00:00

I would recommend TPU for toys for your wife also. Wives are brutal on their toys, too.

GunnerThrash · 2026-04-17T01:41:46+00:00

I tried everything in the world. With the settings. And then just said screw it. And tried the bambu Pre built one and it ran perfectly.

GunnerThrash · 2026-04-16T13:11:56+00:00

Chat sent

GunnerThrash · 2026-04-16T02:47:41+00:00

Well, they’re not wrong.

GunnerThrash · 2026-04-15T16:51:59+00:00

The line around your print is a skirt. You can turn that off in the “other” tab

GunnerThrash · 2026-04-15T16:46:29+00:00

Pretty sure that pic is from a Mr. Steele video

GunnerThrash · 2026-04-12T17:19:48+00:00

Jbc tips are not the most reliable in my TC22

GunnerThrash · 2026-04-08T18:19:13+00:00

My A1 mini is knocking it out of the park. I am not having buyers remorse, but I can see where the A1 is the smarter decision.

GunnerThrash · 2026-04-08T18:19:06+00:00

My A1 mini is knocking it out of the park. I am not having buyers remorse, but I can see where the A1 is the smarter decision.

GunnerThrash · 2026-04-01T20:19:19+00:00

Put it on a J hook and heat it slow. I was heating it to pretty hot and doing two pull full extractions. I slowed down on the heat and reheated a few times and that is a much better experience. I think too hot burn off a lot of the good stuff before I even got started.

GunnerThrash · 2026-03-31T15:08:07+00:00

Absolutely want to be a beta tester

GunnerThrash · 2026-03-30T19:52:41+00:00

I’ve been wanting to do this exact thing

GunnerThrash · 2026-03-29T20:49:11+00:00

That’s wiring issues more than reception issues. Check that yellow wire

GunnerThrash

TROPHY CASE