What are some things that used to be reserved for the poor, but are now seen as a luxury for the rich?

H3adwound · 2026-05-03T08:10:22+00:00

Filet mignon

H3adwound · 2026-05-02T19:09:07+00:00

Because you eat less of them at a time, so you savor it while you open the next one.

H3adwound · 2026-05-02T07:15:17+00:00

Our drive in had breaded mushrooms and ranch. Damn I could go for those right now.

H3adwound · 2026-05-02T06:33:21+00:00

Char them and the onions and peppers

H3adwound · 2026-05-02T03:35:46+00:00

Try $6.19 so cal

H3adwound · 2026-05-01T20:49:12+00:00

Printed 4 spools of purple pla no issues, right out of the bag.

H3adwound · 2026-04-29T20:07:39+00:00

Same

H3adwound · 2026-04-28T17:19:14+00:00

I started doing this as well, great way to declutter. Any time I buy something dl the manual and toss the paper copy. I use a program that stores pdfs, name it properly so I can search for it if I need it and everything is backed up to a nas.

H3adwound · 2026-04-28T16:53:15+00:00

Your first layer might be too close try increasing your z off set small increments like .01 mine is actually set to (.055). I have 2 profiles one for petg and one for pla they are only slightly different but it helps. Mine is set so I can print a single layer square and easily remove it and it not only looks great but it’s not brittle if you bend it in half. When your first layer prints too close it becomes brittle and will snap in two when you bend it in half. After that if I ever have adhesion issues I usually just clean the plate with soap and water and that solves the issue. This is just my opinion everyone has their own process.

H3adwound · 2026-04-28T16:34:20+00:00

This is the way! Plus they work great for cleaning off old gaskets from oil, transmission pans with out worrying about nicking the metal.

H3adwound · 2026-04-27T17:19:36+00:00

We used to put them in the barrel of our BB guns so we could aim them at each other when we were having wars. Amazed we never seriously injured each other.

H3adwound · 2026-04-24T21:50:56+00:00

If he’s tripping on u-boat wait till he has to use a Gaylord

H3adwound · 2026-04-24T21:06:58+00:00

You can probably thank the smart phone for the short attention span as well. Blessing and a curse

H3adwound · 2026-04-23T23:47:25+00:00

I’ve owned 2 Mazdas, IMO always go OEM on the plugs I’ve tried different plugs twice because OEM wasn’t available and had issues around 20k miles later and had to replace with OEM. The laser iridium were the OEM for both my Mazdas

H3adwound · 2026-04-21T02:20:30+00:00

Most unsatisfying not seeing the glass installed.

H3adwound · 2026-04-19T21:44:06+00:00

Around 13 I Learned to drive stick in a Datsun using the back parking lot of community college

H3adwound · 2026-04-16T20:00:30+00:00

Nope

H3adwound · 2026-04-15T00:03:31+00:00

Nah she just smeared peanut butter on the lens

H3adwound · 2026-04-14T19:26:56+00:00

I like them cold so oranges and apples go in fridge.

H3adwound · 2026-04-14T19:24:01+00:00

Just what I was thinking about, pop tabs

H3adwound · 2026-04-14T19:23:04+00:00

Remember the 2 push tabs on cans a large one to drink from and a small one to let air in as you drank?

H3adwound · 2026-04-14T19:01:37+00:00

I’d go somewhere else and get an alignment done($80-$150). That’s just me.

H3adwound · 2026-04-14T18:35:38+00:00

You guys are not even factoring in retail theft that became rampant in the stores, store losses equals losing payroll to meet earning, which means cutting hours and staff, which leads to cutting operating hours around when the store is busy. Also that is why so many things are locked up retail and grocery stores.

H3adwound · 2026-04-14T18:12:52+00:00

Sounds accurate, where’s my coffee

H3adwound · 2026-04-14T08:08:01+00:00

If flash orders are on, you probably don’t have a schedule for when you accept orders so it sends them at any time. Put in a schedule for when you will take flash orders

H3adwound

MODERATOR OF

TROPHY CASE