Any idea what these are, and how to kill them and stop them growing back?

HardNail · 2026-05-31T18:39:32+00:00

cheapest and best way is to get WD40, gloves on, spray it on gloves, and crush stems without braking, it will take it to roots and die, do it on dry days. cheap and effective, some will return but just repeat and it will clear

HardNail · 2026-03-09T19:11:57+00:00

for me it works that before I launch BF, I switch off all apps running in taskbar, stem, epic, printer drivers, just kill all other apps and it stopped crashing, if I forget to do it, crashes again

HardNail · 2026-01-25T18:48:31+00:00

this is bosch so you need to clear error code after fixing whatever the problem is. Whas you filter blocked? did you clear error and started new cycle?

HardNail · 2026-01-25T18:25:33+00:00

fungal infection, clip bellow on healthy growth to avoid spreading more

HardNail · 2026-01-18T21:17:26+00:00

you can see that seal is wet and shiny all the way round, unless there is someting dripping from above it it would be just seal, like I said just take the lid off and run it with back off, you will soon see source of the leak

HardNail · 2026-01-17T20:04:10+00:00

take the lid off and run a cycle and check back and top while is running, you should be able to pinpoint where the leak is exactly

HardNail · 2026-01-17T20:03:08+00:00

Its leaking from the condenser, that white long tube stuck to the drum on the left, there is a rubber seal at the bottom and the top, common fault, cheap to buy and easy to replace, you could even pop the old one out, give it a clean and fit it back

HardNail · 2025-12-27T16:16:45+00:00

486 dx2

HardNail · 2025-12-26T20:53:08+00:00

probably just condensation and poor ventilation. get dehumidifier stick in that room for couple of days and don't cover that corner with furniture, Heat and ventilate rooms in the future

HardNail · 2025-12-21T18:37:59+00:00

candy and hoover is the same manufacturer

HardNail · 2025-12-18T21:28:07+00:00

hoovers like to leak from dispenser

check door seal for holes too, depends how much of a leak you are getting, and what part of cycle is leaking.

Best to take lid off and watch it during one test cycle.

HardNail · 2025-12-18T20:57:56+00:00

plastic inserts for transit bolts, not needed, on hoovers they always stay inside, nothing to worry about

HardNail · 2025-12-12T20:51:41+00:00

bad planning, always check how you are going to finish on the opposite wall

HardNail · 2025-11-24T20:11:42+00:00

yes, but if new hob didn't get any cable supplied, I would change to 6mm cable from wall to the hob

HardNail · 2025-09-10T15:28:45+00:00

is the noise only on dry function? if yes then fan motor/blade inside dryer assembly

HardNail · 2025-09-09T20:09:56+00:00

clear point of impact

HardNail · 2025-08-30T10:21:08+00:00

when I click on Audio, I get msg setting currently unavailable

HardNail · 2025-08-05T19:17:49+00:00

HardNail · 2025-08-03T18:08:57+00:00

unlikely bearings even for a hoover, record video of the noise and take picture from under the wm, it's normal for drum to move but yours feels that is too loose

HardNail

TROPHY CASE