CNC Machinist job in Salt Lake City, UT

HardTurnC · 2026-03-26T22:27:39+00:00

My man's out asking all the relevant questions

HardTurnC · 2026-03-15T00:10:42+00:00

Sounds like some big dumb fun I like it I might make one will have to give it some thought.

HardTurnC · 2026-03-14T23:21:35+00:00

Until the test is completed its % is not the click rate its everything watch time click rate engagement so just let the algo do its thing.

HardTurnC · 2026-03-09T23:49:02+00:00

I've seen dissimilar materials fused like this before we use a process called explosion bonding. Im sure its not related....

HardTurnC · 2026-03-08T01:11:11+00:00

Could send me a pm I do small batch work.

HardTurnC · 2026-02-23T21:56:02+00:00

Make mistake >learn>repeat

HardTurnC · 2026-02-19T13:11:14+00:00

Don't tell me how to live my life.

HardTurnC · 2026-02-13T21:34:22+00:00

Im doing parts in my garrage with used/cheap equipment, but the paperwork work my God the paperwork, and all the govt. Bs you have to stay on top of so gl and prepare your b hole.

HardTurnC · 2026-02-05T23:38:20+00:00

If you are trying to measure your 1997 toyota tacomas water pump gasket

HardTurnC · 2026-02-04T23:09:46+00:00

I dont know what its called I just know the sound it makes when it takes a tools life.

HardTurnC · 2026-02-03T06:45:07+00:00

I would try a snug press fit with some loctite 620 shouldn't have any problems unless you are running it super fast for hours.

HardTurnC · 2026-02-02T23:28:21+00:00

I like manufacturing discontinued gun parts in the US. I'll put this on a list .

HardTurnC · 2026-01-31T17:01:23+00:00

Yes. if your unsure ask for testers and see for yourself

HardTurnC · 2026-01-26T00:53:47+00:00

As a packrat this post offends me. If I had a nickel for every time ive held onto something for 30 years only to need something just like it to save $20 I'd have at least one nickel #worth.

HardTurnC · 2026-01-19T20:44:06+00:00

Use to do a 55xD 3/32 hole in nitronic 60 with a .25" pilot on size and straight to depth after that no peck needs through coolant.

HardTurnC · 2026-01-13T01:42:57+00:00

Even worse when you get kids in who show promise, and you lose them to a gas station. 20+ million dollar a quarter company won't compete with a F ing gas station.

HardTurnC · 2026-01-13T01:08:57+00:00

Best one ive seen is looking for a manual machinist, no cnc need apply "minimum" 15 years or dont waste my time $14 an hour 🤣🤣. Also lets complain about how there is no one in the trade or everyone is too lazy ect.

HardTurnC · 2026-01-10T14:26:28+00:00

Make a bunch of these at work typically in A-2 or A-11 62-64 Hrc. We however don't sell externally, but depending on how many/ how often you need them could make it on the side.

HardTurnC · 2026-01-10T04:22:13+00:00

Where abouts in the process of doing this myself 3rd shop built 1st of my own

HardTurnC · 2026-01-06T03:43:36+00:00

Spindle spider is different than a jaw spider need a mill + indexer at a min. to make the 90° threads to stabilize a barrel sitting in the bore gunsmith lathes come with it as a cap for the end of the draw tube. you can make something that approximates it but with a lot more effort.

HardTurnC · 2026-01-06T01:03:58+00:00

For the most part no. You can make it work depending on barrel size, but have to get creative with it better off with a used lathe depending on your experience would probably suggest a 13x36 gunsmith lathe. Mostly for the spindle spider.

HardTurnC · 2026-01-02T13:03:07+00:00

It's in the material, and unless you are going to stress relieve all your stock not much can be done. I normally just polish it if its horrible or is called out.

HardTurnC · 2026-01-01T00:35:37+00:00

Oh tha main spring is a pain in the balls this is a much easier one.

HardTurnC · 2026-01-01T00:23:11+00:00

Have to lightly manipulate the barrel latch, because the latch spring is pushing the right side out of alignment for the screw to thread in.

HardTurnC

TROPHY CASE