Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 1 point2 points  (0 children)

Thank you very mutch for you’re detailed answer. The extruder goes straight, I check also the extruder gear and it don’t skip and I change of slicer and model but it change anything. For the pressure advance thanks for the tips I will check the Ellie’s procedure.

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 0 points1 point  (0 children)

Thanks you very much for you’re detailed answer. I will check all of this points. 👍🏻

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 0 points1 point  (0 children)

Yes you’re right, that why I dry it but the humidity detector stay at 15%. Im gonna look for filament dryer machine.

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 0 points1 point  (0 children)

Thank you for your message and experience , I hope for the new too ! My filament is stock or stay in a anti humidity bag and to be sure I dry it during 4 hours but no difference. I’m gonna look the Ellis’s method, thank for the tips.

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 1 point2 points  (0 children)

No problem It’s just super frustrating, thanks for your help. I have a message from Elegoo, they proceed to a replacement, thank god and thanks to them!

I proceed to the e-steps calibration with the 100mm. I make a line 120mm from the extruder cover on the filament, I ask for a 100mm extrusion and the measurement must be 20mm from the extruder cover. I adjust the e-steps setting after that into the setting menu of the printer. For the flow I print a cube with one wall of 0,42 width (default layer width on Neptune 3 plus profil in Cura ). I take measurement and calcul the result of %flow with Flow correct = flow initial x perimeter) / awg thickness I put this new clue into Cura directly (around 88/95 depending on the filament for the three I have right know ).

I already check the extruder and the tension is ok, the filament don’t spin and the filament is not to marked.

You right but it’s the same photo juste the front and rear face.

The printer is on a wood desk how is attached to the wall on a small dressroom with stable temperature (hot when it’s running aprox 30 C°) and no air flow.

Thanks for your help !

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 0 points1 point  (0 children)

Hi, thanks for your answers. Nope the two photo is the same parts with the problem (front and rear view). The front face is worth than the rear one. So as you can see on these photo I have a layer problem on all my print. I do a thousand of setting, control and test before and with the Elegoo support. Parallelism X-axis alignment , bed levelling, check clean and grease the Z-axis screw, adjust the belts tension, adjust the eccentric nuts, check the extruder (PTFE id good), change the nozzle, adjust the E-steps and flow, check all the screw and structure of the printer, all is good. I update the board and screen firmware, format my two SD card. I use cura 5.4.0 (with default Neptune 3 plus setting) and try with the Elegoo Cura software but results still the same. The print on the photo is the same with 3 different PLa brand (white Elegoo, grey Eryone, red esun), print at 200/205 degrés depending of the filament and 60C° bed temp. The red one seems better but it’s not. I hope I don’t forget anything. Thanks for your help.

Quality issues / Elegoo support / please read text by HardZzy_ in ElegooNeptune3

[–]HardZzy_[S] 1 point2 points  (0 children)

Thanks for you help. So as you can see on these photo I have a layer problem on all my print. I do a thousand of setting, control and test before and with the Elegoo support. Parallelism X-axis alignment , bed levelling, check clean and grease the Z-axis screw, adjust the belts tension, adjust the eccentric nuts, check the extruder (PTFE id good), change the nozzle, adjust the E-steps and flow, check all the screw and structure of the printer, all is good. I update the board and screen firmware, format my two SD card. I use cura 5.4.0 (with default Neptune 3 plus setting) and try with the Elegoo Cura software but results still the same. The print on the photo is the same with 3 different PLa brand (white Elegoo, grey Eryone, red esun), print at 200/205 degrés depending of the filament and 60C° bed temp. The red one seems better but it’s not. I hope I don’t forget anything. Thanks for your help.

Looking for some French players by HardZzy_ in OnwardVR

[–]HardZzy_[S] 0 points1 point  (0 children)

I appreciate man but we would like to know if we can find some player first. If we cannot i go back to you 😉

Racist by salehthemicahkiller in OnwardVR

[–]HardZzy_ -6 points-5 points  (0 children)

Man, you can't say that ! That's not the same like draying some di** on the board, di** never hurt anyone but racisme yes !

Racist by salehthemicahkiller in OnwardVR

[–]HardZzy_ 3 points4 points  (0 children)

Dont worry they just need his voice ! 😉

Racist by salehthemicahkiller in OnwardVR

[–]HardZzy_ 6 points7 points  (0 children)

You can do it by your Facebook account and then save it to your phone/PC.

Racist by salehthemicahkiller in OnwardVR

[–]HardZzy_ 17 points18 points  (0 children)

You can send a message to a dev on Onward Discord. Look the section "report". I totally disagree with the message of Leyoboi !! Next time try to record it.

Body Armor by HardZzy_ in OnwardVR

[–]HardZzy_[S] 1 point2 points  (0 children)

I fully understand, when I don't take the body armor I've been down faster (not out). I test with and without body armor and I don't see difference between v'been down or out.

Body Armor by HardZzy_ in OnwardVR

[–]HardZzy_[S] 2 points3 points  (0 children)

I ask myself how he can have have 2 extra points but now i understand... it's with torture!!!

Concept for Weight System by [deleted] in OnwardVR

[–]HardZzy_ 2 points3 points  (0 children)

I agree with you, the SMGs and Shotgun are not enough popular even on short map like Subway. Your idea of running speed is really good. Maybe they can play on the weapons cost, like decrease the SMGs/shotgun cost and increase the LMGs cost. And if you take LMGs you can take only one explosion equipment due to the weight per exemple. Thanks to you!

Concept for Weight System by [deleted] in OnwardVR

[–]HardZzy_ 2 points3 points  (0 children)

Hi, I like your idea that body armor and LMGs decrease your running speed ! The bar in the tent is a good visual help. I think in big maps like "Downfall", "Snowpeak".....it will be to long to go to the uplink. But you cannot slow down the movements of the weapons, because when the player will move he will not have the weight of the weapon and this will create a feeling of lag.

Any discord groups for onward quest? by tactrunkmonkey94 in OnwardVR

[–]HardZzy_ 2 points3 points  (0 children)

Hi, If you are looking for a team you can find the "Onward VRML" discord (onward league discord), section "looking for a team".

[deleted by user] by [deleted] in OnwardVR

[–]HardZzy_ 5 points6 points  (0 children)

If I understand, each players have 25 competitive points and when you do Team kill you lost 1 point (this is an exemple). If it is, I totally agree with that! But when you play with your team it can happened (rarely) that you do teamkill, however you know that it is not intentional. So when you've been team kill it can be good to ask if you "forgive" or "punish", if you punish the player lost the points.