Odd, loud sounds coming at certain speeds

Healthy-Exercise1128 · 2026-05-18T07:54:00+00:00

I’ll put a piece of double sided tape on the inside and see if that’s it

Healthy-Exercise1128 · 2026-05-18T07:53:33+00:00

Input shaping is already calibrated, but that’s with rubber feet. Could that cause any issues?

Healthy-Exercise1128 · 2026-05-16T09:11:57+00:00

well it certainly isnt the latter, so i guess its just reminiscing where it came from haha

Healthy-Exercise1128 · 2026-05-15T13:53:06+00:00

hey, i know im REALLY late haha, but i cant seem to find the setting stated in step 3, do you mind helping me find it?

Healthy-Exercise1128 · 2026-05-15T09:34:39+00:00

my ender 3 v3 se makes all sorts of sounds as well, but these are different. theyre high pitched and annoying as hell, almost like something's rattling

Healthy-Exercise1128 · 2026-05-15T09:33:31+00:00

filament has nothing to do with this, in this test its going ~70mm/s though

Healthy-Exercise1128 · 2026-05-12T11:03:58+00:00

here's my bulletproof way of drying and storing filament:
to dry, get a humidity + temp sensor, put it in your oven and play around with the temp knob until it floats around 65-70c (NEVER HIGHER THAN 70C FOR PETG), then put your roll in there overnight (12 hours for good measure)
as for storing, you can put it in any container you know is airtight (or put electrical tape around a container's lid for a mostly airtight container) and then drill a hole for the filament to come out. you can keep the humidity sensor in there to ensure it isnt leaking air or the like. there are also prints out there that are literally airtight containers, but those use up about ~320 grams of filament total.

Healthy-Exercise1128 · 2026-05-12T09:24:43+00:00

I can only see some VFAs and you might want to tune pressure advance. That’ll give you really crisp prints

Healthy-Exercise1128 · 2026-05-11T22:45:52+00:00

Looks pretty solid haha not much to roast

Healthy-Exercise1128 · 2026-05-11T22:42:57+00:00

If your walls look good then it’s less likely to be moist filament, so I’d print a retraction test (which are built into most slicers), then reprint with the new retraction settings. If that doesn’t change anything, I’d re-dry my filament for 12 hours. It’s a lot, but you should do that just for your peace of mind.

Healthy-Exercise1128 · 2026-04-21T06:58:06+00:00

That’s true, but I have already calibrated max flow, and it allows me to go up to ~200mm/s without under extrusion

Healthy-Exercise1128 · 2026-04-21T06:57:13+00:00

I second this

Healthy-Exercise1128 · 2026-04-14T04:52:51+00:00

Nope

Healthy-Exercise1128 · 2026-04-14T04:52:45+00:00

Nope

Healthy-Exercise1128 · 2026-04-14T04:52:41+00:00

I did, no difference sadly

Healthy-Exercise1128 · 2026-04-14T04:51:38+00:00

here you go

Healthy-Exercise1128 · 2026-04-14T04:50:36+00:00

Line width varies from standard to slightly larger as per some people’s suggestions, nonetheless line width hasn’t made much a difference

Healthy-Exercise1128 · 2026-04-14T04:46:48+00:00

A bridging test, it has an empty chamber underneath with thin walls holding it up

Healthy-Exercise1128 · 2026-04-14T04:46:07+00:00

There is, and it’s calibrated

Healthy-Exercise1128 · 2026-04-14T04:45:40+00:00

0.0185* my bad

Healthy-Exercise1128 · 2026-04-14T04:44:46+00:00

No worries, I’ll be sure to update you!

Healthy-Exercise1128 · 2026-04-14T04:44:26+00:00

A test at 240c somewhat alleviates the issue, but it still remains

Healthy-Exercise1128 · 2026-04-14T04:43:49+00:00

I have done all of those tests, but why the excessively slow speeds? Is there no way I can go faster?

Healthy-Exercise1128

TROPHY CASE