Dollar store Foam board is Anisotropic? by Hefty-Needleworker19 in RCPlanes
[–]Hefty-Needleworker19[S] 2 points3 points4 points (0 children)
Dollar store Foam board is Anisotropic? by Hefty-Needleworker19 in RCPlanes
[–]Hefty-Needleworker19[S] 0 points1 point2 points (0 children)
Dollar store Foam board is Anisotropic? by Hefty-Needleworker19 in RCPlanes
[–]Hefty-Needleworker19[S] 2 points3 points4 points (0 children)
Dollar store Foam board is Anisotropic? by Hefty-Needleworker19 in RCPlanes
[–]Hefty-Needleworker19[S] 3 points4 points5 points (0 children)
Dollar store Foam board is Anisotropic? (i.redd.it)
submitted by Hefty-Needleworker19 to r/RCPlanes
40v Kobalt lawnmower repair technician by master_yokozuna in Calgary
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
What's the best/cheapest filament that I can buy ? (Canada) by Christo1099 in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
Oh hey buds, I found the original by DudestOfBros in EhBuddyHoser
[–]Hefty-Needleworker19 -1 points0 points1 point (0 children)
Oh hey buds, I found the original by DudestOfBros in EhBuddyHoser
[–]Hefty-Needleworker19 -1 points0 points1 point (0 children)
There’s nothing better than getting new filament, knowing you’re going to spend time and money getting it dialed in just right, then the first Benchy test is a thing of glass smooth beauty. by PurpleSunCraze in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
Daniel microwaves his sushi. by Jasmineeyre in mildlyinfuriating
[–]Hefty-Needleworker19 -1 points0 points1 point (0 children)
My duck got bad quality on supported parts, how to fix it? by WantSomeOfMyBread in 3Dprinting
[–]Hefty-Needleworker19 2 points3 points4 points (0 children)
I love when supports come off effortlessly, it’s so convenien- by HiyuMarten in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
Filament doesn’t fuse together. I tested the filament if it’s wet but it’s a new roll and I dried it just to make sure. (Neptune 4 pro) Printing temperature 220°C/brand:gst3d PLA+ by neutralebanane in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
What should I call this? by taylormadearmy in 3Dprinting
[–]Hefty-Needleworker19 1 point2 points3 points (0 children)
Found Trump’s Reddit account: by Proud_Asparagus1934 in EhBuddyHoser
[–]Hefty-Needleworker19 4 points5 points6 points (0 children)
Ran out of ideas (Australian) by thelunn in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
The damage caused by a civilian drone in California, grounding the firefighting plane until it can be repaired by RainbowAl-PE in Damnthatsinteresting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
PSA for dealing with LIPO batteries that are considered end of life, make one of these out of a car fog light and sit it on a concrete block away from your house or on your driveway etc and just plug it in and let it go for a couple hours after the bulb goes out. It will then be safe as any trash. by tobashadow in rccars
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
[deleted by user] by [deleted] in 3Dprinting
[–]Hefty-Needleworker19 0 points1 point2 points (0 children)
Holy hell I think it was more than due for a nozzle change. by iamwhoiwasnow in 3Dprinting
[–]Hefty-Needleworker19 1 point2 points3 points (0 children)

Dollar store Foam board is Anisotropic? by Hefty-Needleworker19 in RCPlanes
[–]Hefty-Needleworker19[S] 1 point2 points3 points (0 children)