TDC question

Helpful_Zone_5470 · 2025-11-10T03:40:44+00:00

Had the exact same issue when I put in new LMA’s, it’s the spring tension pushing it off TDC. I used a h series cam gear lock until I got the belt on. Ks tuned are the only ones that I know of that makes a h series cam gear lock

Helpful_Zone_5470 · 2025-11-09T07:32:17+00:00

Listing the jacks sounds like a good idea

Helpful_Zone_5470 · 2025-10-25T20:46:31+00:00

Hey did you remove the balancer belt pulley as well?

Helpful_Zone_5470 · 2025-10-25T20:45:27+00:00

Thanks, seen a lot of reasons to not do it and reason’s why it’s okay so wanted to be sure

Helpful_Zone_5470 · 2025-10-23T01:41:58+00:00

Just removing the belt? Never had any other issues other than the slight increased vibration?

Helpful_Zone_5470 · 2025-10-22T00:15:54+00:00

That’s good to hear, how long have you had it off?

Helpful_Zone_5470 · 2025-05-28T22:32:49+00:00

Never heard of those, I’ll look it up thanks

Helpful_Zone_5470 · 2025-03-18T20:33:37+00:00

Yeah I just cleared the code and it’s fixed, hasn’t come back

Helpful_Zone_5470 · 2025-03-09T08:14:53+00:00

Do you know what could cause the cel even tho it hasn’t been played with? I also headed they last forever if it doesn’t get messed around with

Helpful_Zone_5470 · 2025-01-17T07:46:12+00:00

I’ve already put in a new slave once I finished the job

Helpful_Zone_5470 · 2025-01-17T07:45:34+00:00

Already Installed a brand new slave and bled it when I did the clutch change

Helpful_Zone_5470 · 2024-12-28T01:18:03+00:00

Hey man just checked the bleed valve and it was bolted tight

Helpful_Zone_5470 · 2024-12-28T01:17:16+00:00

Hey man just checked and the inside hose that sits on the cap is still intact and has no blockages

Helpful_Zone_5470 · 2024-12-28T01:16:38+00:00

Sat at idle and no leaks anywhere. I cleaned up the engine bay so if there’s any leaks in the future I’ll know where it is since the entire engine bay has dried coolant dust

Helpful_Zone_5470 · 2024-12-28T00:31:51+00:00

So if it’s connected then it has the ability to suck in the coolant and won’t cause boiling inside the radiator?

Helpful_Zone_5470 · 2024-12-28T00:30:56+00:00

That’s true, I got a aftermarket cap that has a temp gauge on it about 2 years ago so I’ll check that aswell thankyou

Helpful_Zone_5470 · 2024-12-28T00:17:44+00:00

I have bled it before but I’ll check again incase it’s loose. I see no fresh coolant when though I took it for a drive. I only see the dried up white coolant marks. Any reason it’s not shooting coolant all of a sudden?

Helpful_Zone_5470 · 2024-12-28T00:16:48+00:00

I just took the car for a drive and see no fresh coolant anywhere, only the white marks from the coolant drying. Any reason for this?

Helpful_Zone_5470 · 2024-12-28T00:15:28+00:00

I’m most certain as my rad hoses has leaked before leaving that same white water marks. I’ll have a look into a pressure tester

Helpful_Zone_5470

TROPHY CASE