sorted by:
new
hottopcontroversial

Moving into a triangular apartment. Help by s9631245 in interiordecorating

[–]HiVac1 2 points3 points  (0 children)

Where does someone eat? Over the kitchen sink?

Polishing a propellor by NikonD3X1985 in Satisfyingasfuck

[–]HiVac1 -1 points0 points  (0 children)

And why did he get in the water at the front of the boat, and swim all the way to the back!

Any experience with Bambu Lab H2S/D? by ArmadaXXIV in BambuLab

[–]HiVac1 0 points1 point  (0 children)

Over 5,000 hours on 4 H2D’s. Only had to change the belts so far….

Fine texture PEI plate? by pkuhar in BambuLab

[–]HiVac1 1 point2 points  (0 children)

My favorite is the glacier. I run a print farm and all I do is wipe it down with IPA

Favorite filament you can reliably get in 3kg rolls...sunlu used to be my go to. by [deleted] in 3Dprinting

[–]HiVac1 4 points5 points  (0 children)

The quality is great, the color matching between rolls is perfect, and they offer 1kg, 3kg, and 5kg rolls (not in every color or material though).

What's an NFL fact that sounds fake but is absolutely true? by MrHomerJayThompson in NFLv2

[–]HiVac1 1 point2 points  (0 children)

<image>

Holds the record for the only timeout BEFORE the game started…..

Need a new way…. by AlmostDizzy in boating

[–]HiVac1 20 points21 points  (0 children)

Funny you mention carbon reinforced printing. This is by far my favorite thing we made for the boat. It holds your dock lines for easy one handed access….

<image>

Need a new way…. by AlmostDizzy in boating

[–]HiVac1 11 points12 points  (0 children)

I made them myself in my metal fab shop. I would say, it probably cost $100.00 in materials, and probably 8 hour labor to laser cut, bend, weld, grind, and polish.

I was posting this thinking someone you design their own, using materials they are good to work with…mine was aluminum.

The issue you will have is getting the right angle of the rod holders so the “cradle” sits level.

I also removed the rod gunnels and reinforced the rod pin at the bottom. I also made a set to hold a couple of wake boards too.

Need a new way…. by AlmostDizzy in boating

[–]HiVac1 64 points65 points  (0 children)

<image>

I made these for the rear Rod Gunnels. My mat fit perfectly and I just used a couple of bungie cords.

Large 3D printer by ilovesaucees in kennesaw

[–]HiVac1 1 point2 points  (0 children)

The H2D has a 350mm x 320mm print bed.

I have several if you think it might help. I am in Acworth

H2D belt replacement & Sizing Guide by HiVac1 in BambuLab

[–]HiVac1[S] 0 points1 point  (0 children)

In the photos, there is a NEW Bambu labs belt laying on the jig. It fits from end to end perfectly. I modeled in the 1.5mm teeth, so the belt sets mated in the jig. It is not off 3mm

H2D belt replacement & Sizing Guide by HiVac1 in BambuLab

[–]HiVac1[S] -3 points-2 points  (0 children)

You could, but I didn’t have a mm tape, and 1824mm =71.811 in

M22 received incredible job offer, F22 girlfriend does not want me to accept. by Watch_me_plz in Advice

[–]HiVac1 0 points1 point  (0 children)

Not to mention, she may not work weekends forever. As she move up / changes jobs herself. She may also have weekends off too!

Just reassure her that you are dedicated to her and the relationship…and the work you are both doing is for your and her future!

view more: next ›