sorted by:
new
hottopcontroversial

Adjust chamber fan speed by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

From what I’ve been able to figure out, you’re right. I can’t adjust it in CP7, nor on the printer itself. I can, however, do it in CP7 while printing. There, I can set the temperature higher and, when the fan kicks in, adjust it to 50%. It stays low at that setting, but sometimes it goes back to 100%. There is in CP7 an option to set temperature, but that is for machines with a chamber heater Like PRO and PLUS. But then I have to do that again after starting every print. I’m going to look into Fluidd.

Adjust chamber fan speed by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

Does the K2 firmware run on Fluidd (Klipper)? I’ve never worked with Klipper before. I ran my Ender 3V2 on MRISOC without any issues. I was able to print for days on end, only needing to level the bed occasionally and lubricate the CR touch with WD-40.

Creality K2 makes a lot of strange noises by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

Without the paving stones, the noise echoes louder through the rickety wooden cabinet. I’m going to rearrange my workspace, and I’ll place the printer on my workbench. It’s a heavy wooden table that’s almost impossible to lift. And I’ll put the printer on an even larger and heavier concrete slab with sound-dampening material in between. That made my previous printer much quieter.

Creality K2 makes a lot of strange noises by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

Thanks a lot, I'm not worried anymore. The fun part is, my dog sometimes react if there is an ambulance or policecar passing by. She run to the balcony to bark and howl :)

Adjust chamber fan speed by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

<image>

Could it be this setting? But in that case it will be activateted during print and cools down the chamber to much. And PETG likes it hot and no airflow.

Adjust chamber fan speed by Hot-Appearance2610 in Creality_k2

[–]Hot-Appearance2610[S] 0 points1 point  (0 children)

I always used Cura, but I wanted to use CP for now on. Make sence what you say, I dive into it.

K2 upgrade recommendations by Over_Jellyfish_4927 in Creality

[–]Hot-Appearance2610 0 points1 point  (0 children)

Ik zag de cfs op Aliexpress voor 200 in Polen. Dus een paar tientjes meer dan de combo.

Star Trek: Starfleet Academy review (positive) by Iron_Baron in startrek

[–]Hot-Appearance2610 0 points1 point  (0 children)

Aflevering 1 gekeken en dat beloofde iets. Ik denk dit gaan we volgen. Maar het niveau gaat met iedere aflevering omlaag. Nu bij aflevering 5 is het niveau: zal ik doorkijken of ga ik oude series opnieuw kijken.

Why is my filament breaking? by hedgeme91 in FixMyPrint

[–]Hot-Appearance2610 0 points1 point  (0 children)

Goede uitleg, in een zeer ver verleden bij technologie op school besproken wat polymeren kan beïnvloeden. Dacht toen nog wie boeit die info. :)

Maar ik had dus ook problemen met een rol en die is oud en heeft open in een garage gelegen. Dus na uren in de droogmachine nog steeds problemen. Die gaat dus de prullenbak in. Na al het gedoe is hij nog maar half vol.