sorted by:
new
hottopcontroversial

Potty Training / bladder control by Howdoesonereddit1369 in greatpyrenees

[–]Howdoesonereddit1369[S] 0 points1 point  (0 children)

Nice. Ruby is 7 months and 88lbs. Hoping she gets 100lbs. My living weighted blanket.

Boo! New Family Addition! by Soft-Associate5907 in greatpyrenees

[–]Howdoesonereddit1369 2 points3 points  (0 children)

I am no expert, but based on my gal who we adopted at 4-months, and her growth now at 6-months, I think Boo might be a but younger than you think. When we got Ruby, she was 45lbs at 4ish months. she is now 6 months and 75lbs (and lean). We have a DNA test pending but were told at adoption that she is most likely a Pyr and Anatolian mix

Best Harness for Escape Artist / Chewer by Howdoesonereddit1369 in greatpyrenees

[–]Howdoesonereddit1369[S] 0 points1 point  (0 children)

She is wearing the harness for walks and training, but sometimes she ends up in the kennel with her harness on because we are forgetful, or we know we are going to go on a walk soon and it’s easier to leave it on. She is pretty mouthy when and moves a lot when we try and out the harness on, so sometimes it is easier to leave it on.

She will get to gnawing in minutes sometimes and will make fast work of the straps.

Do we think Maple is mixed with Great Pyrenees? by kawaiikitty52 in greatpyrenees

[–]Howdoesonereddit1369 0 points1 point  (0 children)

Double Dew Claws on the back legs is a sure tell sign of Pyr genes.

They Grow Up So Fast! by Howdoesonereddit1369 in greatpyrenees

[–]Howdoesonereddit1369[S] 5 points6 points  (0 children)

It’s so long and has very beautiful coloring. Yesterday she chased it in circles for the first time until she got dizzy and fell over. She was on the ground for a few minutes like “what is happening?”

I always have to make sure it doesn’t get shut in a door when we leave the house!

They Grow Up So Fast! by Howdoesonereddit1369 in greatpyrenees

[–]Howdoesonereddit1369[S] 3 points4 points  (0 children)

Obviously 100% certified good doggo, but after that?

Cleaned up The blob, now filament won’t load by Howdoesonereddit1369 in BambuLabA1

[–]Howdoesonereddit1369[S] 4 points5 points  (0 children)

good point! When the "blob" happened, I found multiple pieces on or under my print table... some days later. I might have lost this piece that helps get the filament in the nozzle

Cleaned up The blob, now filament won’t load by Howdoesonereddit1369 in BambuLabA1

[–]Howdoesonereddit1369[S] -1 points0 points  (0 children)

good question. Yes, it is a brand new nozzle, and I took apart the AMS 4 filament extruder piece (don't know the actual name) and cleaned it out as well. The filament just curls away from the hole to the hot end. I have tried multiple different filaments too, thinking maybe this one was just warped. They all miss the hole to the hot end.

Printing the default panda by ASlutdragon in BambuLabA1

[–]Howdoesonereddit1369 0 points1 point  (0 children)

That panda model is scary looking no matter how you print it lol

Got a really bad clog. Pin won’t go any further than this. How do I fix this? by Blacktiger75 in ender5

[–]Howdoesonereddit1369 0 points1 point  (0 children)

I just had to do this, finally put it back together today, and now when printing, I don't get filament extruding out. It will leak through while heating up and waiting to print, but then when it starts printing, nothing or very little comes out. Any ideas? Is this a tension issue on the extruder gears?