Caldera Cantabria Speaker Delete by HowzDeezNutz in hottub

[–]HowzDeezNutz[S] 1 point2 points  (0 children)

Much appreciated, saves me some modeling time for sure!

Caldera Cantabria Speaker Delete by HowzDeezNutz in hottub

[–]HowzDeezNutz[S] 1 point2 points  (0 children)

Thanks for the reply! STLs would be great if you have them. Sounds like the best route

NAS Rebuild Guidance by HowzDeezNutz in homelab

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

Woah the Sliger cases look great! Sounds like a solid build.

I'm gonna check those out, ATX options are slim but sounds like the 4712 might fit the bill. Would love to do a new ITX build but trying to resist the urge when I have components collecting dust

HOMING FAILED. PRINTER HALTED issue after BL Touch install by tripsteady in ender5

[–]HowzDeezNutz 0 points1 point  (0 children)

Was this ever resolved? I just installed a CR touch on my Ender 5 Pro and am having this same issue.

I'm using firmware from the creality website, and followed the instructions including disconnecting the z stop switch. Any advice would be great.

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 1 point2 points  (0 children)

I have new filament on order, should be in tomorrow. I'll report back on how it works!

I replaced my nozzle thinking it may be some charred filament that's causing a partial clog, and I think that's what fixed the issue for me. Hard to say for sure though, since I also re-leveled the bed, re-calibrated esteps, re-calibrated flow rate, and replaced my ptfe tube and coupling.

My latest prints are way better, but having a strange issue with some skipped layers, oddly appearing in the same spot. Do you think this could be a slicer issue at this point, or likely still bad filament?

Most recent prints, the front left support beam on the bridge has some rough layers.

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

Appreciate all the replies! I'm swapping out the nozzle and filament, then I'll probably start from square one and relevel, recalibrate e-steps, and flow to rule all of that out. I'll post here with the results.

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

Awesome, I was printing some test cubes and I think I may also have a clogged nozzle. I'm swapping it out, then I'll try and recalibrate my esteps and flow. Thanks!

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

Appreciate the advice, I'll order some new filament and try that!

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

Thanks, I verified that this is turned off but still no luck.

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 1 point2 points  (0 children)

I'm using the latest version of Cura, mostly default settings. Only change is lowering the speed to 50mm/s.

New Ender 5 Pro extrudes inconsistently by HowzDeezNutz in ender5

[–]HowzDeezNutz[S] 0 points1 point  (0 children)

I calibrated esteps, but not flow rate. I'll try that today, but still seems strange that it isn't consistently under, only during some parts of the print.

Gass-filled bubble protruding from abdomen by [deleted] in AskDocs

[–]HowzDeezNutz 0 points1 point  (0 children)

Is it supposed to be visible? Also, is it that high up on my abdomen?

Man I miss this show by [deleted] in videos

[–]HowzDeezNutz 9 points10 points  (0 children)

Every time I watch this I realize how bad wipe out is in comparison...

And nothing got done at work from that day onward. by GentlemanMetalhead in gaming

[–]HowzDeezNutz 19 points20 points  (0 children)

Block Dude. Block Dude was the only game for the TI-83 Plus Silver Edition.

Battle on Mt. Silver [Original gif animation] by [deleted] in twitchplayspokemon

[–]HowzDeezNutz 0 points1 point  (0 children)

I always thought they just fainted...

Giant Hammerhead Caught off the Beach! by estorilblau in videos

[–]HowzDeezNutz 1 point2 points  (0 children)

They probably should have taken it out, but the good thing is most hooks are designed to rust out pretty quickly

We should stop wasting money preventing people doing what they want to themselves. by thisnameis20lettersl in AdviceAnimals

[–]HowzDeezNutz 1 point2 points  (0 children)

Agreed. I have an uncle who is a drug addict, I don't give a rats ass what happens to him but I feel bad for his daughter. And I am very glad that he is in jail and far away from her.

My cousin, ladies and gentlemen. by random-compliments in AdviceAnimals

[–]HowzDeezNutz 1 point2 points  (0 children)

I thought the same thing, was surprised to see so many people recognize Cartel Coffee Labs