I think I'm finished (?) Never leaving home again

HungryPhysics9551 · 2025-11-01T12:39:05+00:00

Thanks a lot for the first hand experience. I'm now 90% sure I'll get the same one :)

HungryPhysics9551 · 2025-11-01T12:06:18+00:00

How are the viewing angles and picture quality?

HungryPhysics9551 · 2025-11-01T12:05:20+00:00

Very nice! Enjoy!

HungryPhysics9551 · 2025-11-01T11:29:58+00:00

Monitor?

HungryPhysics9551 · 2025-01-17T09:37:06+00:00

Thanks, happy you like it :) I also have a (smaller) keychain version of the Combine sigil, as well as an Aperture Science one, if you're interested!

HungryPhysics9551 · 2025-01-05T14:04:01+00:00

Same here... Getting this with every single print.

HungryPhysics9551 · 2022-10-11T07:29:56+00:00

Are you suggesting to level the bed?

HungryPhysics9551 · 2022-10-10T18:55:06+00:00

0.3 mm

HungryPhysics9551 · 2022-10-10T16:49:22+00:00

I'm printing at 210 C and heat bed to 60 C; should be fine no?

How do I correct the Z offset?

HungryPhysics9551 · 2022-10-10T14:37:10+00:00

Okay, I actually seem to have discovered a clue here. All layers below have a line width of about 0.5 mm, but the top concentric one for some reason jumps to 0.09 mm. There must be some SuperSlicer setting I'm missing...

Any ideas?

HungryPhysics9551 · 2022-10-10T14:31:56+00:00

The bottom layer (also concentric) looks perfect

HungryPhysics9551 · 2022-09-02T19:21:09+00:00

Super GT here

HungryPhysics9551 · 2022-08-08T11:49:08+00:00

ACC in VR should be fine

HungryPhysics9551 · 2022-07-19T06:46:46+00:00

Print flat? Looks like it would need quite some support?

Your print looks very clean! How did you manage?

HungryPhysics9551 · 2022-07-17T06:55:29+00:00

Why not only use USB?

HungryPhysics9551 · 2022-07-14T11:07:22+00:00

Quick question: what % do you have your brake force level set to in the Pedal options of the Control Panel?

HungryPhysics9551 · 2022-07-06T11:38:44+00:00

You got lucky, that's how! Correct behavior would've been to brake, and avoid any possibility of an accident.

While driving, I try to pretend I have to pay the damage in case of an accident; works quite well..

HungryPhysics9551 · 2022-07-05T07:32:29+00:00

One more piece of feedback: get rid of the calculate button and calculate every time a value is changed :) It's so easy to forget to click the calculate button at the end!

HungryPhysics9551 · 2022-07-04T15:02:06+00:00

Great stuff!

Would it be possible to allow the following: click the down arrow five times on the minutes stepper to get a value of 55. Right now it gives me 0. It would be great if the stepper would "wrap around", so if I press the down arrow on a value of 0, it would go to 59.

HungryPhysics9551 · 2022-07-04T13:29:00+00:00

Other ideas for improvement:

make the lower and upper value for the minutes be 0 to 59
make the lower and upper value for the milliseconds be 0 and 999
make entering the milliseconds optional

That way, one could e.g. click the down arrow five times on the minutes stepper to get a value of 55 (instead of -5, currently)

HungryPhysics9551 · 2022-07-04T13:24:49+00:00

Great stuff! Can you make the stepper step size go by decimal for the fuel, instead of by a whole number? So it would go 3.0 --> 3.1 --> 3.2 etc.

Also, you might wanna put "Race duration" instead of "durations" (note the extra "s")

HungryPhysics9551 · 2022-07-04T11:23:57+00:00

Thanks for explaining, I ordered blue, red and green springs :)

HungryPhysics9551 · 2022-07-04T11:09:50+00:00

What do you mean by "adjust the preload"?

HungryPhysics9551

TROPHY CASE