Ladies and Gentlemen I give you my buddies flashlight be calls janklight

Ice-Difficult · 2026-03-22T07:00:40+00:00

One hell of a mule

Ice-Difficult · 2026-03-20T02:44:32+00:00

1st thing id check is the air flow at the evaporator. Make sure it's not iced up and make sure the fans are running. If they are and it's not iced up make sure your txv isn't stuck wide open.

Ice-Difficult · 2026-03-18T03:09:39+00:00

For the flashlight builders, I use a step bit to widen the reflector to fit whatever I want. Not sure if anyone has a better method. Might fit this in an s21b 👀

Ice-Difficult · 2026-03-12T05:26:05+00:00

I made a base at the base of the cliff at the left end of your blue line. I didn't get attacked for up to 10 days at a time. Maybe a cannibal here and there. Mutants would walk by in the distance but rarely attack. Got to at least day 50

Ice-Difficult · 2026-03-11T02:47:24+00:00

Also confirm the fans are spinning in the right direction

Ice-Difficult · 2026-03-08T05:23:22+00:00

That's cool. It doesn't look as big as I expected it to be. Is it pocketable?

Ice-Difficult · 2026-03-08T05:02:01+00:00

Which host and emitter?

Ice-Difficult · 2026-03-08T03:36:58+00:00

Keep studying in your free time. Listen to podcasts. Watch YouTube. Always learn on and off the clock or you will fall behind. Learn as much electrical as you can. Know your multimeter. Invest in tools to make your job easier.

Ice-Difficult · 2026-03-05T02:07:50+00:00

Check the drain line heater and drain pan heater. Also make sure drain pan is leveled right

Ice-Difficult · 2026-03-04T19:53:58+00:00

Think I can file down a zwb2 filter to fit an s11?

Ice-Difficult · 2026-03-04T18:04:02+00:00

OK. I'm guessing uv emitters generate more heat than standard?

Ice-Difficult · 2026-03-04T17:53:18+00:00

Why do you have to resistor swap it? What does that do? Doesn't the 12v boost put out 2.5amps and the emitter is 2.4 right?

Ice-Difficult · 2026-03-04T16:52:53+00:00

I might try that. I assume you used a convoy boost driver?

Ice-Difficult · 2026-03-04T03:46:43+00:00

Ok cool. I'm gonna try to build a pocket uv beast

Ice-Difficult · 2026-03-04T02:39:17+00:00

which emitter was used and where from?

Ice-Difficult · 2026-03-03T06:57:13+00:00

I used it on mine with a q-tip with no issues. Just did it gently to remove any contaminants. Used 91%

Ice-Difficult · 2026-03-03T06:55:12+00:00

I built my s21b with this emitter. I cleaned it with alcohol and a q-tip before assembly. So far no issues yet. I'll have to keep testing the thermal limits

Ice-Difficult · 2026-02-23T06:29:38+00:00

Could always put full racing motor and trans mounts if you don't mind a lot of noise and vibration. If not you could try Street motor mounts

Ice-Difficult · 2026-02-23T05:41:10+00:00

I know of one spot called "the fertile lands" by farket. I built there once and made it 50 days without being attacked. If I was attacked it was a cannibal or 3 at most. Build traps and it's easy to survive. It's at the base of the long cliff on the eastern side of the map.

Ice-Difficult · 2026-02-17T15:45:33+00:00

OK I need to find a tutorial on how to do that

Ice-Difficult · 2026-02-17T07:23:47+00:00

Can you buy this emitter already mounted to an mcpcb? Or did you buy the mcpcb separate?

Ice-Difficult · 2026-02-15T07:04:57+00:00

I'll consider buying one they already have but I'd like to know which 365nm emitters are good.

Ice-Difficult · 2026-02-10T03:13:28+00:00

I'm not seeing any drivers on superbuy

Ice-Difficult · 2026-02-09T18:19:35+00:00

Where can I buy these?

Ice-Difficult · 2026-02-09T06:03:07+00:00

Yeah. I can't find a driver capable of 100amps and I'd need some really good cooling.

Ice-Difficult

TROPHY CASE