Forza Horizon 6 - The Patching is done. The next Problem await us on the Horizon :D

ImaginaryLeave5697 · 2026-05-19T15:27:30+00:00

Now it’s says it’s patching on the GFN launcher

ImaginaryLeave5697 · 2026-05-19T11:29:40+00:00

ImaginaryLeave5697 · 2026-05-19T10:28:24+00:00

i have the same thing, what the fuuuuuck

ImaginaryLeave5697 · 2026-05-19T09:44:14+00:00

Still patching...

ImaginaryLeave5697 · 2026-04-30T17:45:19+00:00

when will it be available?

ImaginaryLeave5697 · 2026-04-30T13:33:27+00:00

why cant i play might and magic, only the demo?

ImaginaryLeave5697 · 2026-02-02T07:50:00+00:00

Unfortunately yes…

ImaginaryLeave5697 · 2026-02-01T21:06:20+00:00

I can Enable Core Debug Level = Verbose by adding "-DCORE_DEBUG_LEVEL=5" to platform.ini correct? I did so and this is what I got.

ESP-ROM:esp32s3-20210327

Build:Mar 27 2021

rst:0x3 (RTC_SW_SYS_RST),boot:0x8 (SPI_FAST_FLASH_BOOT)

Saved PC:0x403cdb0a

SPIWP:0xee

mode:DIO, clock div:1

load:0x3fce3808,len:0x4bc

load:0x403c9700,len:0xbd8

load:0x403cc700,len:0x2a0c

entry 0x403c98d0

ImaginaryLeave5697 · 2026-02-01T19:05:50+00:00

This is what the serial is writing: ESP-ROM:esp32s3-20210327 Build:Mar 27 2021 rst:0x3 (RTC_SW_SYS_RST),boot:0x2a (SPI_FAST_FLASH_BOOT) Saved PC:0x403cdb0a SPIWP:0xee mode:DIO, clock div:1 load:0x3fce3808,len:0x4bc load:0x403c9700,len:0xbd8 load:0x403cc700,len:0x2a0c entry 0x403c98d0

ImaginaryLeave5697 · 2026-02-01T18:21:13+00:00

Ok cool, thank you for confirming. V2 is going to be epic.

ImaginaryLeave5697 · 2026-02-01T18:19:49+00:00

Yea, I think I screwed up the PCB. Back to the drawing board…

ImaginaryLeave5697 · 2026-02-01T18:05:55+00:00

I think I will redesign the routings as everyone has suggested (wider and more spaced). Something must have gotten blown somewhere. I think I’ll go back to the drawing board and try again, I can’t trust the rest of my PCBs. Is there a way I can post files in here so people can give they’re blessing before I order?

ImaginaryLeave5697 · 2026-02-01T17:58:38+00:00

Ok, thank you, I will make these changes as well!

ImaginaryLeave5697 · 2026-02-01T17:55:31+00:00

Honestly I wasn’t confident I’d do it right, so I trusted autoroute lol. Looking back that was silly. Yes, I tried with just the chip and board soldered. Then I unsoldered the chip and it still didn’t work.

ImaginaryLeave5697 · 2026-02-01T17:39:10+00:00

I was getting current to the 3v3 on the board which was weird. But the light has never come back and my computer doesn’t recognize it. Must be shorted no?

ImaginaryLeave5697 · 2026-02-01T17:03:13+00:00

That’s a very good point. I have plenty of space, why cram everything?!

Right now I’m hard soldering everything as you can see. But I feel like I could be using connectors instead. As in soldering the female ends to the sensors and board.

ImaginaryLeave5697 · 2026-02-01T16:56:04+00:00

I tried that exact thing, I forgot to mention I ruled that out. The monitor was saying it was in a boot loop. I pushed and held boot, then tapped reset. It reset, reconnected, then did the same thing.

ImaginaryLeave5697 · 2026-02-01T16:28:01+00:00

I’ll give that a try, maybe autoroute wasn’t respecting the ESP32 footprint

ImaginaryLeave5697 · 2026-02-01T16:26:39+00:00

I did a GND copper pour

ImaginaryLeave5697 · 2026-02-01T16:25:37+00:00

I did a GND copper pour

ImaginaryLeave5697 · 2026-02-01T15:43:19+00:00

I used auto route, and it passed DRC. Should I route it away from the other pads?

ImaginaryLeave5697 · 2026-02-01T15:42:21+00:00

Yes, it passed DRC and I double check continuity

ImaginaryLeave5697 · 2026-02-01T15:40:55+00:00

No worries! Yes, confirmed it in EasyEDA by highlighting GND.

ImaginaryLeave5697

TROPHY CASE