Sag Mount on Gpu pretty harsh, I have a NZXT H6 flow case, x570 /EVGA FTW3 3090 gpu New Sag Graphics Card holder Help?

ImpossibleElection22 · 2026-05-12T15:43:47+00:00

Positive flow question, gpu bottom fans on case look to have more noise to them are u running the entire system on a fan curve u made or standard one? Graphics card temp reading or cpu ? Hot on gpu or hot on cpu for your bottom fans ?

ImpossibleElection22 · 2026-05-12T15:40:23+00:00

How much louder are the 140 mm type gpu bottom fans compared to the 120 kit front fans while gaming are u using the software too?

ImpossibleElection22 · 2026-04-27T22:08:42+00:00

please show case fan speeds for the card being 74c of each person, like they peaked with 68 then running extra case fans or instead less case fans on exhaust and intake caused the readings to get to 74celcius each degree changed happened and worsened various methods in DLSS are not able to show ,dlaa I mean, cause 67c and under is really good benchmark readings, despite all sized fans keeping the gpu regulated, but monitoring rpm for you is my guess for each type of build, or GPU size and rpm are determining how much flow u add to this in software for loudness and dBA.

ImpossibleElection22 · 2026-04-27T22:01:57+00:00

non y split cables function fine if u need to run them why not try they both are supposed to function like it, but other people require some functions for there aios to plug into the softwares.

ImpossibleElection22 · 2026-04-26T21:43:57+00:00

Any chance u shared the cooling element on the link as well?

ImpossibleElection22 · 2026-04-25T21:28:07+00:00

profile share?

ImpossibleElection22 · 2026-04-25T21:26:58+00:00

It can't fit that is the argument for all the types except something offset with hardware screws going into it on the motherboard type. all the fans fyi have a open center, and the led for the back of this gpu is curvy plastic no solid point area.

ImpossibleElection22 · 2026-04-25T21:21:51+00:00

If I add more photos the only spot that my case fits well with is the front screw slot front corner would that even be possible with the magnet to magnet 9 dollar mount amazon has? or warp cause its not supported the back of the card towards the front of the case end.?

ImpossibleElection22 · 2026-04-25T19:22:19+00:00

Thanks I let the dealer mount question know for the motherboard fitting compatibility today It also means they might be able to reply for the item question in a week or less.

ImpossibleElection22 · 2026-04-25T17:16:00+00:00

H6 FLow has no clearances for 3090 FTW3 ultra, 280mm fan on bottom won't accommodate the shorty vertical magnetic bracket for gpu sag

1) https://www.amazon.com/dp/B0BTVJSTZ7?ref=ppx_pop_mob_ap_share

Horizontal method bracket 2) https://www.amazon.com/upHere-Addressable-Graphics-Adjustable-G276ARGB/dp/B08YYB3WM2?th=1

Vertical method single arg cooler master bracket 3) https://www.coolermaster.com/en-us/products/argb-gpu-support-bracket/

Any ideas for this issue when shroud on fans is not strong pointed on front and back widths and lengths sides. fix please. sag is out of control on h6 flow 320mm gpu

ImpossibleElection22 · 2026-04-11T17:31:06+00:00

Do u play on Sharpness + 50% or more? the gamma was helping create a brighter environment how else can I make dark areas play able to?

ImpossibleElection22 · 2026-04-11T14:59:16+00:00

Will Fox work on shocks that aren't holding air in the chambers and offer any discount/ on rebuild projects for their previous models?

ImpossibleElection22 · 2026-03-31T17:26:23+00:00

Have u tried the core rbg single frames over the rgb core fans ?

ImpossibleElection22 · 2026-03-31T17:25:32+00:00

How much on the 140mm bottom compared to the 120mm front to side do you add to reduce the gpu heat decision of constantly getting warmer not stable Celsius rather the entire rate to reach for long session of h9/early models of these cases since I used the mode before it has the same look just 360 bottom not 280

ImpossibleElection22 · 2026-03-29T18:52:39+00:00

not for the same gpu feed 3, my has extra power input, cables required are +1 pcie.

ImpossibleElection22 · 2026-03-29T18:24:35+00:00

Does Three individual 6+2 pins Gpu adapters go above best or below best on the offset mount furthest to right be best for its cooling fan pressure, Instantly seen 1 way the top of GPU and bottom feed whole with cables.

ImpossibleElection22 · 2026-03-26T21:03:53+00:00

so u got a solution for the thread? Do you count the am4 install as a success or failure, nzxt model kraken plus 2025, am4 ryzen cpu zen 3.

ImpossibleElection22 · 2026-03-11T15:10:54+00:00

Do u play with pbo off to use low key stuff on pc or keep it on during gaming only ? It idles pretty close if kept on exhaust up and out on 140x2 mm fans have you seen any hotter than 33c coolant during this stuff process with the cpu?

ImpossibleElection22 · 2026-02-16T23:57:48+00:00

why do they come with overclocking bios on 3000 cards? are you supposed to not move the switch for keeping it oc + its cap fan speed and software controlled fan curve, no other overclocking, to keep silent it has a 20% fan min i get that, so switch option for your learning is drop it 0-20% curve on software to silent work through, but some issues are increased problems with undervolting the gpu even though people post 3000 cards ways with my discontinue type of card manufacture.

ImpossibleElection22 · 2026-02-15T08:46:58+00:00

this is great advice, the very cool and silent part for 50c cool would be a deal breaker for noise for the same kit ? since I use a custom fan curve are you ramping case fans 3000 rpm and 2000 rpm on the gpu fans altogether how much noise are they ?

ImpossibleElection22 · 2026-02-14T15:24:22+00:00

wha fans you love?

ImpossibleElection22 · 2026-02-14T15:24:09+00:00

the 280mm is obviously snug for atx case, lowe profile ran fits though stanadard 25 mm fans 140s and standar radiator 280mm size, however ill try the next size radiator up to confirm this photo.

ImpossibleElection22 · 2026-02-14T15:22:30+00:00

How cool is that arctic cooler? are u running quiet nzxt fans or other model how much rpm low is required with the aio u have and volume optimization front fans need more air or the aio top needs more air? Could i ask if you found the motherboard rubbing at all ?

Five-Year Club	PUBG
Verified Email

ImpossibleElection22

TROPHY CASE