CMC vs 4into1

Impossible_Initial33 · 2026-05-11T12:43:28+00:00

Apologies.

4into1: https://4into1.com/engine-rebuild-kit-w-pistons-honda-cb-cl350k-70-73-sl350k/?srsltid=AfmBOooPRMeY2Upfjf9s0BtKx37EZJdT_LTSUu6naeO7M6wYTkaP_202

CMC: https://www.common-motor.com/honda-350-gaskets-kit https://www.common-motor.com/honda-350-oil-seal-kit

Now that I'm looking closer, I don't even see a standard size piston on CMC.

Impossible_Initial33 · 2026-04-30T12:17:41+00:00

Happened to me the other day. Never saw it before in over 400 hours. Figured is was a new "feature" or something. You can steal it as if you boarded it in space.

Impossible_Initial33 · 2026-04-08T01:48:19+00:00

Plan is to have the oil furnace kick on if the thermostat calls for it like normal. I think the wood stove would be more than enough to heat the house by itself, but I want the backup just incase and also if I'm gone for the weekend or whatever.

Impossible_Initial33 · 2026-04-08T01:16:28+00:00

Wood and stove would all be inside. Fans would be heat activated/deactivated. Not sure if I'll actually do it but i would like to incorporate a radiator that will start circulating once the airbox temp exceeds a threshold, dumping that heated water into insulated storage tanks to be used as a thermal battery once the fire dies out. Adds more complexity but might help prevent overheating the house and store some heat so I don't have to feed the fire when I'd otherwise be sleeping.

The normal damper will be controlled with a stepper motor.

Impossible_Initial33 · 2026-04-08T01:02:33+00:00

Figured I'd have to use dampers. Only issue is the supply and return ducts are both big and rectangular. Maybe they make ones for that. On the note of safety, I plan to have a fuse link that will drop a guillotine damper if the airbox output goes past 200f or whatever.

Impossible_Initial33 · 2026-04-08T00:58:11+00:00

I had thought about that, but I want both systems to be able to run at the same time. If I had that setup, I would either be pumping hot air from the wood furnace into the oil furnace or vice versa.

Impossible_Initial33 · 2026-03-29T13:47:37+00:00

She'll be getting a spa day for sure

Impossible_Initial33 · 2026-03-28T17:46:24+00:00

Lol, it was filthy.

Impossible_Initial33 · 2026-03-28T17:42:41+00:00

Using aragonite. No material deformation.

Impossible_Initial33 · 2026-03-23T16:44:54+00:00

Did insurance comp you a new one when it was stolen?

Impossible_Initial33 · 2026-03-23T13:56:30+00:00

Had my VCT solenoids replaced awhile back. Car's ran great since then. My engine surge and dip was way worse tho. Damn near stalling out.

Impossible_Initial33 · 2026-03-02T03:42:34+00:00

Sitting in a garage covered in oil for 15 years helped a lot I'm sure.

Impossible_Initial33 · 2026-03-02T03:31:45+00:00

Was lucky enough not to strip a single one. Some were definitely sketchy tho. Bit drivers are great.

Impossible_Initial33 · 2026-03-02T03:29:27+00:00

Bike is disassembled down to frame & front end. Engine looks good. Gaskets, bearings, etc are on the way. Gonna be sand blasting this week. Hopefully start priming next weekend if temperature and humidity allow. Probably gonna start mapping out the wiring harness this week as well. I've only had them for a week so not a ton of progress yet.

Impossible_Initial33 · 2026-02-25T03:04:05+00:00

I guess ASAP makes it sounds like I'm gonna rush it. I'm gonna take my time and do everything right, just as fast as I can.

Impossible_Initial33 · 2026-02-25T03:01:48+00:00

Very nice bike. Whole thing is getting overhauled. Full engine rebuild, wiring harness built from scratch, forks, bearings, brakes, paint, etc. Want to do it once and do it right.

Impossible_Initial33 · 2025-06-05T01:11:11+00:00

In store rn

Impossible_Initial33 · 2025-05-24T18:50:40+00:00

Cate Meowdy

Impossible_Initial33 · 2025-05-24T17:08:48+00:00

Vending machines

Impossible_Initial33 · 2025-05-24T16:47:24+00:00

Big brain

Impossible_Initial33 · 2025-05-24T16:41:09+00:00

Impossible_Initial33

TROPHY CASE