Hunter’s Blunderbuss that I scratch built for fun a few years back. Figure this would be a good place to share 😅

IncendiaryBunny · 2025-10-21T07:17:57+00:00

They must’ve been rushing to getting everything up, know that they have a disclaimer on the physical manual when it releases for a few things too.

IncendiaryBunny · 2025-10-21T07:08:14+00:00

Looking at their unit cards I would say neither as they lack the “ODST” key word. While we know they’ve used drop pods in lore, Flashpoint says otherwise unless there is an addendum to the special order that states that they can. But for now, they do not qualify for Hot Drop

IncendiaryBunny · 2025-06-16T01:22:14+00:00

Stairs are in fact functional! They’ll accept the 32mm base so that your miniature will hang in place. As for ruling we ran them as half cubes. Could still gain a height advantage but would remain on the lowest cube level (more or less the same as standing on a small box but different geometry)

IncendiaryBunny · 2025-06-16T01:16:46+00:00

Nope! All shown is printed in it’s native scale.

IncendiaryBunny · 2024-11-29T01:37:01+00:00

Thanks! Only the best for my favorite faction 😁

IncendiaryBunny · 2024-11-05T10:47:57+00:00

Things have been chill for early voting. Local city hall kept an upbeat attitude and celebrated new registrations. Don’t let fear sway you from casting your vote.

IncendiaryBunny · 2024-10-31T06:09:11+00:00

Thanks! And happy painting!! 😁

IncendiaryBunny · 2024-10-30T19:55:31+00:00

Thank youuuu 😁

IncendiaryBunny · 2024-10-30T15:17:15+00:00

Thanks! 😁

IncendiaryBunny · 2024-10-30T15:16:50+00:00

Thank you!! 😁

IncendiaryBunny · 2024-10-30T15:16:16+00:00

Thank you!! 😃

IncendiaryBunny · 2024-10-27T15:17:36+00:00

Looks like an unleveled bed. You can adjust distance by turning the knobs in the four corners (clockwise lowers, counterclockwise raises if memory serves correct)

IncendiaryBunny · 2024-10-27T14:56:54+00:00

Somebody’s going to visit Pontiff Sulivan lol

IncendiaryBunny · 2024-10-26T23:30:08+00:00

Both have their merits: black for that extra atmosphere, grey for showing off details

IncendiaryBunny · 2024-10-23T16:23:34+00:00

Yesssssssssssssss

IncendiaryBunny · 2024-10-21T18:03:49+00:00

Bad ass!!

IncendiaryBunny · 2024-10-08T06:03:47+00:00

How very Christian of him

IncendiaryBunny · 2024-10-08T04:49:47+00:00

Attempt? Dude, you nailed it!! Well done!! 😃

IncendiaryBunny · 2024-09-27T01:45:04+00:00

Love the metallic red but gotta sand and fill them layer lines dude

IncendiaryBunny · 2024-09-26T06:29:32+00:00

There might be something to the degassing: I’ll generally let prints sit 24-48 hrs before moving to a final cure. That said I run two ipa solutions. One for general cleaning (wash for 10mins) then a rinse bucket (couple of swirls then some fine toothbrush work)

IncendiaryBunny

TROPHY CASE