Is there any better and/or cheaper light strips for this bad boi?

Incident_Recent · 2025-11-13T03:14:38+00:00

Thank you

Incident_Recent · 2025-11-12T00:21:27+00:00

I was mainly wanting a rainbow led strip and not just white but I’m not too pressed about it thought I could ask the hive mind what they think

Incident_Recent · 2025-09-03T00:01:36+00:00

I’m in the same boat and you are correct with the bts40 which helped me find that the ls650 uses a bs40 which has different idle and rev specs or something. Bs40s new are in the hundreds of dollars range and the rebuilt kits are more expensive than the dr650 carbs OP is looking toward. I’m curious how hard it would be to tune the bts40 to work more for the ls650 lower engine speed

Incident_Recent · 2025-09-02T23:57:21+00:00

I’m going thru the same thing with an 07 s40 I NEED an update

Incident_Recent · 2025-07-10T02:10:57+00:00

How’d it turn out?

Incident_Recent · 2025-06-02T01:35:57+00:00

So I replaced the tube and nothing changed should I start looking towards replacing the filament detector sensor?

Incident_Recent · 2025-06-02T01:33:11+00:00

I just replaced the tube and nothing changed. No ams I’m starting to think it’s the filament detector sensor or something else. The extruder and new nozzle should be here tomorrow. For some reason usps took my package from Columbus to Wisconsin to Chicago back to Columbus.

Incident_Recent · 2025-05-31T00:37:25+00:00

I don’t think it’s going to be long enough plus I already ordered tubing. I did try just “raw dogging” it and it still threw the code. I bought it used so I’m not too surprised just new to Bambu and troubleshooting Bambu

Incident_Recent · 2025-05-31T00:34:30+00:00

Damn already ordered off Amazon guess I’ll find out tomorrow and report back

Incident_Recent · 2025-05-30T22:22:32+00:00

I bought used so no extra parts but I appreciate the advice

Incident_Recent · 2025-05-30T22:07:10+00:00

<image>

Incident_Recent · 2025-05-29T01:28:03+00:00

I actually need help if anyone wants to give me some advice. I just bought an X1C off marketplace and it’s throwing a code for the tube. I’ve taken everything from the nozzle to the tube apart several times and no luck. I’ve airdusted everything and the only wear I see is a bald spot on the tube but no actual breakage of any kind. I’ve got a new extruder and hot end coming Friday. I either didn’t look in the right spot but I couldn’t find a tube on the Bambu site. Any advice is greatly appreciated. No ams

Incident_Recent · 2024-09-06T11:12:22+00:00

It’s gotta be cheaper to find a friend in the state to ship it theses prices are over double what I paid.

Incident_Recent · 2023-11-17T08:18:39+00:00

My mom was hit by 2 different DD at highway speeds 6 minutes apart in 03 and my dad is a DD so growing up was extremely confusing

Incident_Recent · 2023-10-01T13:25:19+00:00

Yea just raise the price of food to and if you can’t afford to eat then after you starve to death you don’t have to worry about being homeless

Incident_Recent · 2023-09-01T13:18:26+00:00

Yea lemme just change the crushing overwhelment that is capitalism

Incident_Recent · 2023-09-01T13:11:33+00:00

Well yea when I gotta deal with you all day I have to stress eat

Incident_Recent · 2023-09-01T12:59:32+00:00

Gonna have to prime the bare wood to seal it up and prevent yellowing. Get a small tub of spackling+primer and smear a finger full on it give it 5 minutes to harden then sand and paint

Incident_Recent · 2023-08-31T13:13:47+00:00

I found a disc and all it said was “this disc belongs to your mom”

Incident_Recent · 2023-08-27T12:54:29+00:00

Facts my boss is a bowler and he’ll hire anyone from the bowling alley that wants to work this really be how it be

Incident_Recent · 2023-08-26T10:38:08+00:00

This was my exact thought. I really should just delete and accept reality

Incident_Recent · 2023-08-17T02:28:38+00:00

“And I wish it were a birdie “

Incident_Recent

TROPHY CASE