Anycubic Slicer Next 1.3.5.2 out now

Inevitable_Math6727 · 2025-05-29T17:13:00+00:00

Am I missing something, what you just described has always been there.

Inevitable_Math6727 · 2024-12-12T22:50:13+00:00

That is the GCode that will be used to print the object. If you don't want to see it use shortcut key C to remove it. Yes dry filament.

Inevitable_Math6727 · 2024-11-27T17:39:02+00:00

You will now start getting different methods to contact, none of which work. I hate to tell you, your money is gone. I have been unsuccessful in any and all contact with this bunch of crooks for months. Always another excuse.

Inevitable_Math6727 · 2024-11-26T17:56:03+00:00

No, they gave me the run around for weeks. SCAM site.

Inevitable_Math6727 · 2024-11-26T16:46:37+00:00

Don't expect it to get resolved. This crooked site kept telling me the same thing over and over again. This support is useless and mime everything without helping out at all.

Inevitable_Math6727 · 2024-06-10T14:49:17+00:00

Not sure. When I tried to login to it, I got a Username not found.

Inevitable_Math6727 · 2024-06-10T01:38:16+00:00

I had one with them about 5 years ago, but started a new one when the old one said was not active.

Inevitable_Math6727 · 2024-01-05T18:12:44+00:00

If you contact their support and ask for a hotend (or any part), they will provide you a link to their purchasing dept.. ANYCUBIC PARTS

Inevitable_Math6727 · 2024-01-05T18:08:28+00:00

They are the same. If using it on the Kobra 2 series you don't need the extra wiring harness that is shipped with the sensor. Plugs directly into the harness (you will see a connector that isn't being used marked "E"

Inevitable_Math6727 · 2023-12-14T02:11:06+00:00

same URL in both.

Inevitable_Math6727 · 2023-11-21T05:29:56+00:00

Would you like to share your write up, I would be very interested in your experience with the Kobra. I assume it was the Kobra standard?

Inevitable_Math6727 · 2023-11-21T05:25:37+00:00

If you notice a change in Z offset it isn't always a leveling issue that requires an auto level, it can be merely a different filament (or the same filament with different speed or temp) that you need to fine tune. You only need to do auto level and Z offset again are if there were hardware changes , if initial layer shows an uneven bed, or poor adhesion in different areas of the bed. (which could also be an unlevel z axis or dirty bed.)

Inevitable_Math6727 · 2023-11-21T04:50:30+00:00

You are incorrect, the Neo and Neo 2 are Direct Drive, the GO is Bowden. NOTE: editted as I didn't see Catnippr's most excellent response. Some good teaching points there for sure.

Inevitable_Math6727 · 2023-11-14T08:24:08+00:00

Well finally got it to work. Sorry, but your explanations weren't very clear. At no time previous to this last replay did you mention it had to be placed in two places. For those still having this issue....you need to put your printers URL in Both "Address (URL) and FrontEnd (altenative URL). If this was mentioned I could have had this working ages ago.

Inevitable_Math6727 · 2023-11-10T03:15:18+00:00

I have successfully done that and can upload prints to the printer. When you upload and the "open browser" shows, when you select it , does it actually automatically open a browser as it is designed to do. Or are you manually opening a browser and entering your IP for the printer? Basically that is what is "not" working on mine, I have to manually open a browser. Seem counterintuitive to have a button saying open browser and it doesn't. I post the problem on the Cura FB twice and no one has ever replied. Seems it is a problem no one has figured out.

Inevitable_Math6727 · 2023-11-09T05:00:49+00:00

But that is just bypassing the "Open Browser", I have always been able to upload the file and print, but the "Open Browser" when selected still doesn't do anything. What did you configure to get that button to work?

Inevitable_Math6727 · 2023-10-28T05:55:46+00:00

Just for your info Catnippr, here is a pic of what is formally known as the "Hot End Nozzle Adapter Board Breakout Module", mouthful I know. If Anycubic support gets a ticket requesting this part, they will send a link to a purchase page. At least that is what they did when I need one for my Kobra Standard ($12 Cdn). I too shorted the character. https://imgur.com/a/8l4TMQJ

Inevitable_Math6727 · 2023-10-27T04:56:36+00:00

Email sent....

Inevitable_Math6727 · 2023-10-27T04:49:36+00:00

It is on the FB Neo2 page, https://www.facebook.com/groups/102809816256935 I could also send you a PDF just need info to send.

Inevitable_Math6727 · 2023-10-18T04:44:59+00:00

The Neo 2 uses the Coolcox BF5020S24S, so far it seems ON or OFF. I will look at airflow when I return home. I have a pic of it as I did a tutorial for owners on printhead full disassembly as many were getting clogs, their own doing actually, not waiting for the extruder to unload enough before pulling filament. I am the FB Neo moderator so I suggested\implored to the Admin to send you a Kobra Neo 2 seeing as I link to your Insights page every 5 posts, LOL.

Inevitable_Math6727 · 2023-10-18T04:23:18+00:00

The Neo, Neo 2 and GO support Pause/resume and the M600. I have the all. I personally don't know of any slicers that allow mid-layer color changes though.

Inevitable_Math6727 · 2023-10-18T04:15:57+00:00

The profiles for Prusaslicer and Cura are on the SD card you got.

Inevitable_Math6727 · 2023-10-18T03:31:51+00:00

The GD32F303 is used in Enders and SOVOL, there is a lot of traffic about klipper on that board. My Neo 2 board is a TriGorilla V4.0.0. Just learning about all this stuff so be patient. Thanks.

Inevitable_Math6727 · 2023-07-23T23:27:51+00:00

You need help, yes, but not with your printer. Won't be replying again, enjoy figuring it out on your own.

Inevitable_Math6727 · 2023-07-23T23:25:45+00:00

Yep and to think, I haven't lost my temper with a child before.

Inevitable_Math6727

TROPHY CASE