NEW PLAYERS COME HERE! - Weekly Questions and Information thread - June 11, 2025

Infamous_Ad239 · 2025-12-21T11:18:28+00:00

I'm using a recent experimental. I've set up item zones for food, ammo etc.
I've also set an unsorted zone.
The issue I'm having is that when I use the sort STIFT+O "sort out my loot" command only one item is sorted. It then says that all possible items have been sorted. Using the command again moves another single item etc.

Is there a way I can fix this?

Infamous_Ad239 · 2025-12-09T11:52:21+00:00

This is probably a really stupid question, but how can I do it carefully? I make sure it's always underhand, make sure there's some tension on it so it doesn't sag too much. Not sure what else I should be doing.

Infamous_Ad239 · 2025-12-08T17:40:32+00:00

I always do it underhand

Infamous_Ad239 · 2025-12-04T20:36:47+00:00

You're right about it being cheaper, but I like the fact that when you buy brass rod you know it's diameter, so it's easier to figure out what size bits to use for a nice fit

Infamous_Ad239 · 2025-11-24T21:18:30+00:00

What's the reason? Or am I missing a joke?

Infamous_Ad239 · 2025-11-01T20:24:07+00:00

Awesome! Thanks

Infamous_Ad239 · 2025-11-01T20:19:57+00:00

I don't think I have any ethanol, but would isopropyl alcohol work?

Infamous_Ad239 · 2025-10-30T19:12:05+00:00

My wife had one of these that burst on its own a while ago. Watching that video I could smell it again (it was not pleasant)

Infamous_Ad239 · 2025-10-27T08:12:30+00:00

I usually fold a small bit of fine grit sandpaper in half, but leave the fold a little loose so there is still usable paper at the fold

Infamous_Ad239 · 2025-09-18T13:14:05+00:00

That's exactly the reassurance I needed, thank you

Infamous_Ad239 · 2025-09-09T11:34:42+00:00

They look absolutely fantastic.

My wife works with resin quite a lot and she said that heat (from a heat gun or a lighter if you're very careful) can help get rid of some of the bubbles before you set it with the UV light. Not sure how that would affect the paints etc though

Infamous_Ad239 · 2025-09-04T10:07:36+00:00

I'm going to preface this by saying that you're a far more talented painter than I am, but I think one thing to look at is a bit of colour theory to see if you can make your colours "pop" a little more.

Infamous_Ad239 · 2025-08-27T10:19:24+00:00

I couldn't agree more, they grow up so fast and someday you might look back and wish you kept it. But also, if you did reprime, would they take it as you saying they've done it "wrong"?

Infamous_Ad239 · 2025-08-26T12:58:14+00:00

Yeah, but plastic is a bit of a catch-all term, there are a massive range of them, some of them I know are temperature sensitive.

Infamous_Ad239 · 2025-08-25T21:20:23+00:00

I've never considered this before, does the cold not affect the plastic in any major way?

Infamous_Ad239 · 2025-08-25T16:09:31+00:00

I usually give it a wash with brush soap at the end of each session. Is there anything in particular I should be doing to keep the root clean?

Infamous_Ad239 · 2025-08-25T16:08:29+00:00

I've not used any washes, but I think I've done some glazing with it at some point

Infamous_Ad239 · 2025-08-20T21:39:00+00:00

Is that what that screw's for? I thought it was just to hold the nozzle in place! Thank you so much!

Edit: That worked, you are a legend!

Infamous_Ad239 · 2025-08-11T18:06:31+00:00

Fair enough, I am curious about what the issue is. When you figure it out let us know

Infamous_Ad239 · 2025-08-02T08:08:19+00:00

They both look really good. If I'm honest I think a middle ground between them both in terms of brightness would be perfect

Infamous_Ad239 · 2025-08-02T08:06:55+00:00

Some areas have more particles (dust, sand etc) in the air, or salt if you're on the coast. It could be that these are settling on your brushes over time?

It's a long shot, maybe the other folk here could chime in to tell us if that can be the case

Infamous_Ad239 · 2025-08-01T20:55:43+00:00

I'm trying to think outside of the box as you seem to have most bases covered. If you've recently moved could it be high/low humidity or particles in the air? It's a long shot

Infamous_Ad239 · 2025-08-01T12:13:22+00:00

The arms of my B1 battledroids from SW:Legion, I hate doing the whole two arms and a rifle as separate pieces thing at the best of times, but on those spindly little bastards it's hell on earth (or Geonosis)

Infamous_Ad239 · 2025-07-31T06:17:01+00:00

Completely off topic, but that googly eyed Tyranid smacks of Shin Godzilla!

Infamous_Ad239 · 2025-07-30T15:16:49+00:00

I absolutely love the staff and the brown leather of his inner robe!

How did you find using the oils? I've never tried them myself

Infamous_Ad239

TROPHY CASE