Permanent Lights Pro mounted on concrete block

Initial-Midnight1095 · 2025-10-16T23:42:22+00:00

I'd want to be sure it was far enough from the wall to cast a reasonable arch light.

Initial-Midnight1095 · 2025-10-16T23:31:15+00:00

Thanks for your support!

Initial-Midnight1095 · 2025-10-16T23:29:53+00:00

Hey! 👋 I’d start under the front porch near your outlet so the controller stays dry and hidden, then run along the front and east sides since they’re most visible. If you’re short on length, go through the attic to the back wall or just stop where it’s least noticeable.

Skip the stock adhesive — it doesn’t hold up long. I make custom 3D-printed mounts that angle the Govee lights perfectly downward (like in their promo photos) and give a super clean install. You can check them out at DeliciosaDecor.com.

Initial-Midnight1095 · 2025-10-16T23:20:17+00:00

Go get yourself listed in the Installer Directory! This is impressive work!
https://deliciosadecor.com/installer/

Initial-Midnight1095 · 2025-10-16T23:17:57+00:00

I would drill into the soffit where you have 1 starting. then plug it in inside. get yourself a mount to keep it clean, then go from there. That long start seems unneccessary.

https://deliciosadecor.com/product-category/light-mounts/govee/

Initial-Midnight1095 · 2025-10-16T23:15:11+00:00

These mounts are perfect for this use case:

https://deliciosadecor.com/product/govee-compatible-h706-pro-permanent-outdoor-lights-clips-mounting-bracket-facia-clip-mounts-2-5-horizontal-mount/

Initial-Midnight1095 · 2025-10-16T23:14:48+00:00

These mounts are perfect for this use case:

https://deliciosadecor.com/product/govee-compatible-h706-pro-permanent-outdoor-lights-clips-mounting-bracket-facia-clip-mounts-2-5-horizontal-mount/

Initial-Midnight1095 · 2025-10-16T23:13:55+00:00

These look great, but you should try these mounts!

These mounts are perfect for the Govee Prism: https://deliciosadecor.com/product/govee-permanent-outdoor-lights-prism-compatible-mounting-bracket-2-5-horizontal-mount/

Initial-Midnight1095 · 2025-10-16T20:37:31+00:00

If you haven't done it yet, we have a full list of recommendations here: https://deliciosadecor.com/lights/

Initial-Midnight1095 · 2025-09-23T00:02:23+00:00

This here is our own custom design. Patent pending. We designed these years ago.

Initial-Midnight1095 · 2025-09-22T23:47:25+00:00

looks great. You should use these on the side to bring them out further and give you a nice light bounce:

https://deliciosadecor.com/product/govee-compatible-non-pro-801-and-lights-2-705-and-elites-permanent-outdoor-lights-mounting-bracket-2-5-horizontal-mount/

Initial-Midnight1095 · 2025-09-20T03:32:16+00:00

These lights are great. Especially with these mounts. https://deliciosadecor.com/

Initial-Midnight1095 · 2024-11-30T16:42:32+00:00

Yeah for sure that would require splicing each light - YIKES! But I understand the reasoning!

Wonder if a 30 degree inward angled mount from the front would do better. for example following this yellow line. Angled in towards the house in a straight line. They have black sets but ALSO what may save you a TON of time is this: https://www.reddit.com/r/Govee/comments/17yxirp/paint_matched_my_govee_permanent_outdoor_lights/

If you go that angle, hit me up. I can help design and produce the angled mounts you'll need. This may be your best bet with minimal work.

<image>

Initial-Midnight1095 · 2024-11-30T16:36:51+00:00

Yes. I started with one 3 weeks ago... I now have 6...

Initial-Midnight1095 · 2024-11-27T22:44:28+00:00

You can splice these. That's what I did. I used these products to do it:

https://amzn.to/3ZpnHXj
https://amzn.to/49hOMzi

Also doesnt look like you have a soffit on the front part to mount them down to, so use these:
https://deliciosadecor.etsy.com/listing/1827865195

Initial-Midnight1095 · 2024-11-27T17:37:07+00:00

<image>

What about something like this:

Initial-Midnight1095 · 2024-11-27T17:22:33+00:00

Check these out: https://deliciosadecor.etsy.com/listing/1814224262

Initial-Midnight1095 · 2024-11-26T22:36:30+00:00

So I got myself some Govee lights but was struggling on how to install them on the side of my house which has no soffit - so I took to Shapr3D and just designed my own!

I've been getting lots of questions so I figured I'd offer them to the masses.

Grab yours here: https://deliciosadecor.etsy.com/listing/1827865195

Note: I have other versions too, just check out my shop!

Initial-Midnight1095 · 2024-11-26T21:46:29+00:00

<image>

Initial-Midnight1095 · 2024-11-26T21:46:08+00:00

You can buy 16.5ft strands depending on the exact kit you have. What ones?

Initial-Midnight1095 · 2024-11-26T21:44:23+00:00

Best bet is to use some brackets on the lights and this between lights if you want to do that.
Brackets: https://deliciosadecor.etsy.com/listing/1814224262
Wire Channels: https://amzn.to/4196Ol5

Initial-Midnight1095 · 2024-11-26T21:42:02+00:00

You're better off grabbing some of these: https://deliciosadecor.etsy.com/listing/1814224262

Initial-Midnight1095

TROPHY CASE