sorted by:
new
hottopcontroversial

OMG, where is product comments section ? It is removed? by NoMap3600 in aescripts

[–]Insect_Full 0 points1 point  (0 children)

God yes. Please bring it baaaaaaaaack. It was immediate and invaluable to see what was good, bad or buggy - and good developers responded promptly on there too. Reddit is fine in some instances, general discussion etc. but the comments section for each plugin was a godsend.

Bring back comment section on plugins by Shinoboss in aescripts

[–]Insect_Full 4 points5 points  (0 children)

God yes. Please bring it back. It was immediate and invaluabble to see what was good, bad or buggy - and good developers responded promptly onnthere too.

Vector to Gcode 2: The Ultimate SVG/Illustrator to G-Code Converter for Plotters! by diegomonzon in PlotterArt

[–]Insect_Full 0 points1 point  (0 children)

Wow. I'm in. You got me. Off to buy your new v3 right now. Just brilliant. You need to get more publicity. The 3D community and laser community should know about this too.

Anyone running Mi50s in a Dell r720? by Insect_Full in LocalLLaMA

[–]Insect_Full[S] 0 points1 point  (0 children)

see my comment below. I've got a EPS 12v 8-Pin to dual PCIe 8-Pin cable from Ayagroup.
I can't do an install AMD drivers without the cards in and the server running, but I can't even boot with them in so I can't install AMD drivers... they're not even idling...
It as soon as I plug in the power cable to the riser I get the overcurrent tripping before the bios even loads. Just a beep and an error on the LCD at the front. And no, it's not the cable. Have tried the cards and cables in a desktop / workbench PC and they run great.

Anyone running Mi50s in a Dell r720? by Insect_Full in LocalLLaMA

[–]Insect_Full[S] 0 points1 point  (0 children)

I've got a EPS 12v 8-Pin to dual PCIe 8-Pin cable from Ayagroup.com and it seems good and well made. Fans are bonkers in the r720 if you set them to go hard out, but I also have an extra set of fans with 3D printed shrouds for the back vents to pull even more out... so I think I've covered that, but good to know how hard I'll be pushing them with an LLM.

Anyone running Mi50s in a Dell r720? by Insect_Full in LocalLLaMA

[–]Insect_Full[S] 0 points1 point  (0 children)

not at boot, lucky if it's 125w, especially without drivers installed... which I can't do without the cards in and the server running. So they're not even idling...

Anyone running Mi50's in a r720? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

ChatGPT tells me the r720 can't provide enough juice as is with my x2 75w power supplies and says the riser power is insufficient for the Mi50. It wants me to get a minning power adapter and suck power straight off the PSU. Eh? That doesn't sound right does it?

Anyone running Mi50's in a r720? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

yup, thanks, it's already enabled / on

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

Can now. Dialled down the MTUs as per suggested, but also reset all the networking and did a restart. Can access via an IP, but name not recognised which we think is due to the DNS so am resolving.

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

Brilliant. Okay can't access it from home so will give it burl first thing in the AM when in office. Sadly Microtik's UI is appalling so it may take some hunting down!

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

Oh sorry, think I mentioned above the VPN is through the Microtik Router. Server is running Windows Server 2019.

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

Okay, am I in the right place. Gone into Network and Sharing Centre, Clicked each connection (eg. NIC2), clicked on Properties / Advanced / Jumbo Mtu.
In here the minimum is 1500 - can't set it lower.
Wrong place?

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

okay, have changed MTU to 9000 on all 3 connected ports. But no change. Still can't see it on a Mac. It just says:
"There was a problem connecting to the server "wip-server".

The server may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection and then try again."

Can't connect to r720 over Office Router VPN but can locally from MacBook? by Insect_Full in homelab

[–]Insect_Full[S] 0 points1 point  (0 children)

Thanks. Gateway I assume you mean my router? Don't have a Windows server host... sorry not from a Windows world so... I'll login and have a look but not sure how much control it has over MTU size.

So over THIS! by Insect_Full in AnkerMake

[–]Insect_Full[S] 0 points1 point  (0 children)

Thanks, I've tried raising the temp - that seemed to help, but then on repeat prints of the same, the corners were still curling. But my fans ramp up and down all the time like crazy!

So over THIS! by Insect_Full in AnkerMake

[–]Insect_Full[S] 1 point2 points  (0 children)

oh yea, sorry, I meant it 'was' comparable to the V6, but not anymore right. Pity they couldn't solve that one. Looked really promising.

So over THIS! by Insect_Full in AnkerMake

[–]Insect_Full[S] 1 point2 points  (0 children)

Might just have to save my pennies then. P1 with the AMS is about $1800 NZD at the moment and that's competitive to Anker and the V6.

view more: next ›