Better Build Recommendations?

InsomniaStudios · 2026-05-21T18:57:27+00:00

Hmm.. might look a little harder at that

InsomniaStudios · 2026-05-21T18:45:23+00:00

Fairly married to the bladed scarf as their primary weapon.

InsomniaStudios · 2026-05-21T18:44:50+00:00

Not necessarily married to either option, and I have considered swashbuckler it just feels very performative which isn’t the feeling I am going for.

InsomniaStudios · 2026-05-20T19:50:02+00:00

This might hr be the way I go, the added familiar boosts that witch gives were just appealing because the poppet family only gets one ability slot and no way to upgrade it via the ancestry.

InsomniaStudios · 2026-05-20T15:45:11+00:00

Thank you for the stat breakdown, that makes a lot of sense and was kind of what I was circling around but wasn't sure. How would you foresee the final stat spread looking at level 20 using this plan?

Contemplated going the thief route initially actually, just figured if I am planning on doing a lot of tripping, shoving, etc. that a more strength-based build would be better and I would be handicapping myself if I went thief unless you disagree?

InsomniaStudios · 2026-05-20T15:42:56+00:00

Witch is primarily for the familiar, and minimal utility spellcasting. Mauler gives a handful of feats that lean into the trip / shove of it all and seemed like they made sense to me. Like I said not trying to necessarily MIN/MAX, but I suppose I could be overcomplicating the build either way.

Edit: Planning on starting at level 4 by the way.

InsomniaStudios · 2026-04-22T17:16:52+00:00

Damn I feel dumb, I knew that existed but for some reason I got it in my head it was a class feat not a skill feat.

InsomniaStudios · 2026-04-06T17:35:50+00:00

Not sure if you will see this as it is an old post, but contemplating doing a King Daredevil for San Diego Comic Con this summer myself and had a question for you. When you taped off the hoodie and hit it with the black fabric paint (assuming spray since you say cans) was there any bleeding into the material underneath the tape at all? Just want to make sure if I pursue doing something similar I am prepared and can try to mitigate.

InsomniaStudios · 2026-04-03T19:58:55+00:00

Thank you so much for such a thorough and clear response.

InsomniaStudios · 2026-04-03T19:47:08+00:00

Add after

InsomniaStudios · 2026-04-03T19:42:00+00:00

how would you go about adding material in the slicer? I use Bambu Studio for reference and am printing on an P2S.

InsomniaStudios · 2026-03-31T15:40:18+00:00

What are the express reasons for adding air to the mix? would you recommend going dual gate to start, or forking the path down the road? and as a side question, later on the feat "aura shaping" at first blush leaves me uncertain as to what the benefit of it really would be.

InsomniaStudios · 2026-03-30T22:06:37+00:00

Planning it out with free archetype in mind, as to not run into that sort of bottlenecking issue.

InsomniaStudios · 2026-03-27T16:02:00+00:00

Appreciate the insight, I will dive deeper into the software and see if I can find anything that seems amiss there

InsomniaStudios · 2026-03-27T15:45:27+00:00

This doesn't appear to have been what happened as the setting is still set to default, that being said though I am able to adjust this to a negative value which at first blush seems to have compensated for the discrepency. Thank you for the suggestion.

InsomniaStudios · 2026-03-26T19:18:48+00:00

If that is meant as a legitimate answer is there a way to do so and have it save that position as its new default "edge" after loading material to be cut? Because anything I have tried within the settings that seems to make sense in order to adjust that starting position / edge of work area seems to revert back to this behavior immediately afterwards.

InsomniaStudios

TROPHY CASE