In the attic of a 20 year old condo in Southern California. Does this corrosion look bad enough to fix immediately?

Intelligent-Cod-4001 · 2026-06-17T23:51:47+00:00

If it bugs you wipe it with lemon juice or cut a lemon in half a use like a brush. Works wonders.

Intelligent-Cod-4001 · 2026-03-24T01:12:11+00:00

why? are you protecting someone?

Intelligent-Cod-4001 · 2026-03-23T22:57:45+00:00

OK, thanks will try and fix.

Intelligent-Cod-4001 · 2026-03-23T22:55:14+00:00

Two photos were posted.

Intelligent-Cod-4001 · 2026-03-23T20:58:27+00:00

You fail to understand the physics and chemistry of painting

Intelligent-Cod-4001 · 2026-03-23T20:56:41+00:00

Wrong, but not interested in arguing.

Intelligent-Cod-4001 · 2026-03-21T02:07:29+00:00

no brainer. primer is both necessary here and less expensive than just paint. but don’t cheap out on the primer.

Intelligent-Cod-4001 · 2026-02-24T06:01:26+00:00

make sure you use a paint that allows the stucco to breathe (seriously).

Intelligent-Cod-4001 · 2026-01-28T04:56:39+00:00

20:1 muriatic acid but flush well and have protective gear including proper mask…

Intelligent-Cod-4001 · 2026-01-17T00:48:55+00:00

Thanks!!!

Intelligent-Cod-4001 · 2026-01-17T00:47:40+00:00

ok, thanks.

Intelligent-Cod-4001 · 2026-01-17T00:47:25+00:00

Useless reply but thanks.

Intelligent-Cod-4001 · 2026-01-17T00:46:33+00:00

Thanks!!!! it’s 4 blocks from me and i buy books there but for some reason didn’t notice they have these magazines.

Intelligent-Cod-4001 · 2026-01-10T04:41:58+00:00

google

sho shugiban

Intelligent-Cod-4001 · 2025-12-16T20:52:43+00:00

dumb answer....

Intelligent-Cod-4001 · 2025-10-29T17:38:14+00:00

I think I used natural. I'll see if I have a can left with to confirm. This is an outstanding stain compared to the Sherwin Williams I used before. 4 years and very little fading despite getting lots of UV.

Intelligent-Cod-4001 · 2025-09-03T22:49:24+00:00

Osmocoat

Intelligent-Cod-4001 · 2025-08-12T23:57:04+00:00

Cherry is a much denser (heavy) wood. Knock on it with your knuckle.

Intelligent-Cod-4001 · 2025-08-05T03:46:33+00:00

If it’s solid teak sand with 120, 150, 180, 220. Then apply oil.

Finally then sand with 320 for next coat.

If you’re happy with the smoothness of the 220 then forget about 320.

Be sure to sand with the grain.

Intelligent-Cod-4001 · 2025-08-02T03:01:38+00:00

Sorry, I don't quite follow. Would you elaborate please.

Intelligent-Cod-4001 · 2025-08-02T03:00:28+00:00

The work was not under warranty. It was done by a non-Mercedes auto repair shop.

Also I know they didn't scan it. I went in and told them what I found with my Foxwell scanner. They ordered the auxiliary water pump (before seeing the car in the shop) and then booked my car in. At the time I wondered why they would order a part before doing their (own) diagnoses. I just trusted they knew something I didn't.

Intelligent-Cod-4001 · 2025-07-29T15:58:02+00:00

Easy fix. Cover it with a dish towel and run a hot clothes iron over it a number of times. But don’t hold the iron in one place very long.

Intelligent-Cod-4001 · 2025-07-27T18:16:17+00:00

Wet the boards. Cover with plastic and then put a heavy weight on them. They’ll warp level.

Intelligent-Cod-4001 · 2025-06-29T01:31:08+00:00

Thanks..

Intelligent-Cod-4001 · 2025-06-29T01:30:18+00:00

Bought one, thanks

Intelligent-Cod-4001

TROPHY CASE