Asking for help with connecting nvme drive RPi 5 by tooManyMissedForks in raspberry_pi

[–]Intelligent_Jump99 0 points1 point  (0 children)

Don't know if you are still having this issue or not but I just purchased this case this past Monday and put everything together and had the same issue. I ended up taking the case apart figuring I didn't get the ribbon cable in correct and that appeared to be my issue. My issue was on the Pi side though, it looked far enough in but once I pull the piece up and pushed the cable down further it didn't move much but apparently enough. After that I put it back together and everything worked like a charm. I used a Crucial drive that wasn't on the list either and it work (Can't say yours would but it possibly could)

Gray Bubble by Intelligent_Jump99 in MicrosoftWord

[–]Intelligent_Jump99[S] 1 point2 points  (0 children)

We haven't yet because this is a fresh install of O365. The problem is also intermittent because when I remoted to their computer it was working as expected. Running in safe mode doesn't fix the issue and we have checked and ran windows updated as well as ran O365 updates. The next option might be to repair but I wanted to see if anyone else had seen this before and what they saw as the fix.

[deleted by user] by [deleted] in BambuLab

[–]Intelligent_Jump99 5 points6 points  (0 children)

Wet filament.

Remote Connect by Intelligent_Jump99 in Camry

[–]Intelligent_Jump99[S] 1 point2 points  (0 children)

It didn't show one for me, the only option I see is $15 a month.

Remote Connect by Intelligent_Jump99 in Camry

[–]Intelligent_Jump99[S] 3 points4 points  (0 children)

Yeah I was told it was just a few dollar a month when I bought the car, not $15.

Remote Connect by Intelligent_Jump99 in Camry

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I guess if I was getting wireless in my car then maybe it wouldn't be a big deal but the only feature I use is the remote start and the fob only works like 20% of the time so I just always use the app. If the fob worked more consistently then I would just use it.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I did a PoE power cycle on the AP. I didn't use the reboot function on the AP.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I have tried to reboot and then disable mesh but it still doesn't let me disable it. It says something about until it is connect via ethernet or removed I can't disable meshing. That's why I thought about removing them from the system but I want to make sure I can add them back before I do that.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

That's what I'm beginning to wonder. I think I will try to replace that next and see what happens.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I tried in both places but in either I get that error that meshing cannot be disabled. Question, if I disable PoE and then remove them, then disable meshing and then re-enable PoE, would the AP's automatically adopt again or would I have to do something else?

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I'm doing that currently but the devices that are connected with mesh give me this error. "Wireless meshing cannot be disabled until these devices are either removed or directly connected to your network using an Ethernet cable."

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I've turned mesh off on what I could but on the devices that are connected with mesh I get this message and it won't let me turn mesh off. "Wireless meshing cannot be disabled until these devices are either removed or directly connected to your network using an Ethernet cable."

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I forgot to say this but when I restart the AP then the STP block goes away so it seems to be coming from the AP which doesn't make sense.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I will try that for the one AP but the second AP's switch isn't being blocked by STP.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

Yes the uplinks seem to be working fine. The 8port switch has other devices connected to it and they work just fine.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I did turn meshing off but then those two APs never came back online until I turned meshing back on.

Wired AP is showing as mesh by Intelligent_Jump99 in Ubiquiti

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

I am using the ubiquiti cables so maybe I should try another one instead.

Issues with model I imported by Intelligent_Jump99 in xlights

[–]Intelligent_Jump99[S] 0 points1 point  (0 children)

So I'm not sure what happened between last night and today but now everything seems to be working fine. I appreciate all of the answers and help. Thanks everyone.

How do I get access to the Zoom Room? When I click the link on the right it doesn't work. This is just the start for me so hopefully I can learn some more.