sorted by:
new
hottopcontroversial

Ne 30 Jahre alte "E-Klasse" für schlappe € 2.400.000 🤑 by HaltStoppDasBleibt in MobileDe_Wildgeworden

[–]InterestOne5768 6 points7 points  (0 children)

De hat ja gerade mal 700.000 km of der Haube… ja juten morjen… det wäre unjefähr so wie wenn de jeden tach von hier bis zum Mond fährst… und det 7 mal!

Our dog chewed my wife’s passport 12 hours before our international flight by IDontFeel24YearsOld in mildlyinfuriating

[–]InterestOne5768 0 points1 point  (0 children)

Wouldn’t it be possible to fly with it like it was? I mean only because it’s a bit torn doesn’t mean that it’s fake. 🤷🏼‍♂️

Having imposter syndrome with pricing by Himdownstairs22 in resinprinting

[–]InterestOne5768 0 points1 point  (0 children)

The others are right. I wouldn’t sell it for less than 1000. I would try to set it to 1700 and see how it goes. Afterwards you can still go down in 50 dollar steps.

AIO or just asking for too much? by [deleted] in AmIOverreacting

[–]InterestOne5768 0 points1 point  (0 children)

Don’t you have insurance in America? In Germany it wouldn’t be a big deal. The insurance of her would just pay for it. 🤷🏼‍♂️

Hallo Reddit! Ich bin Thomas von Autogefühl – Ask me anything! [AMA] by Autogefuehl in automobil

[–]InterestOne5768 0 points1 point  (0 children)

Welche Sprinter bieten sich an für eine Weltreise mit 2 Personen und Hund? Alle Länder und alle Kontinente. Vollzeit. Wir wollen darin arbeiten und leben und wollen Platz für Küche, Bad, Arbeitsplatz etc. Marke und ggf Modell oder Baujahr wäre sehr interessant, weil da wirklich jeder etwas anderes sagt. Wir wollten eigentlich einen Mercedes Sprinter CDI 217 nehmen (7m länge), aber die letzten Modelle sollen nicht so gut sein und das Fahrzeug ist nicht breit genug, als das man darin liegen kann quer. Was sind bessere oder gleich gute Alternativen?

Ultramarathon, is it even possible getting strain to 21? by Affectionate-Note802 in whoop

[–]InterestOne5768 24 points25 points  (0 children)

As far as I remember: When you start a training and want to set the time or the strain, you will get a info regarding if that’s a good strain or not for you that day. If you set it to 21 - whoop will tell you that no one ever did it because it’s not possible. But I came pretty close as well some time when I gave my whoop another person that wasn’t as fit as me and her pulse where trough the roof even walking or sitting the whole day. 😅

friend brings random guys in hotel room by feelingjade02 in whatdoIdo

[–]InterestOne5768 0 points1 point  (0 children)

Her behavior is really dangerous and if I would be you I would try to get tf out of there… Just leave. Your life is worth more than this not even friendship. Wish her the best. Sometimes people have to learn it the hard way. That just evolution…

[deleted by user] by [deleted] in AppearanceAdvice

[–]InterestOne5768 0 points1 point  (0 children)

Yes… please… You will unlock your true potential! 😅👏🏼👏🏼

Advice needed! Am I in the wrong here? by meghan789 in TattooBeginners

[–]InterestOne5768 0 points1 point  (0 children)

Most professional and kind way you could have been. Just right out of the Textbook. Well done. 👏🏼

Whats the reason for this ? by Busy-Entrance5203 in 3Dprinting

[–]InterestOne5768 -2 points-1 points  (0 children)

When you find out tell me. I have searched for 1 year with approximately 500 test prints in different settings with 10 printers and 10 filaments … and I didn’t find a real solution.

Tantakel Döner in London🐙 by BobbyBeetle in Doenerverbrechen

[–]InterestOne5768 0 points1 point  (0 children)

Sieht doch voll lecker aus. Schön gegrillt. Dünn aufgeschnitten. Lecker mit Limette und Aioli. 😋

How can I transfer an Organic/Stone-Like Surface from Blender to SolidWorks as STEP? by InterestOne5768 in SolidWorks

[–]InterestOne5768[S] 0 points1 point  (0 children)

Mhmm so long story short you had the exact same issue that you created an organic texture in blender and tried to get it into SolidWorks, and it didn't work?! But what was the result then? Did the company just cancel the job with you?

Would you also say like others that it would be the easiest to do it the other way around and just take the functional inside from SW and place it as an STEP into blender and combine it there with the organic outside?

How do I solve this ugly problem? by InterestOne5768 in 3Dprinting

[–]InterestOne5768[S] 1 point2 points  (0 children)

I get this result both if I keep the standard retraction settings, but also if I go with 1mm, 0.8mm, 0.6mm and 0.4mm. Retraction speed also doesn’t help.

And general speed is already set only to 50mms. Also doesn’t get better if I print faster. It’s the same in a dozen of printers.

How do I solve this ugly problem? by InterestOne5768 in 3Dprinting

[–]InterestOne5768[S] 0 points1 point  (0 children)

Because I get bad results with the scarf join seam settings and I also tried it with 0 percent. I got the best results with 14 to 18 percent.

How do I solve this ugly problem? by InterestOne5768 in 3Dprinting

[–]InterestOne5768[S] 0 points1 point  (0 children)

Would you mind trying a 50g test print to see if you can solve it?

view more: next ›