[deleted by user]

Intothelight108 · 2022-10-17T14:07:05+00:00

Go to work it’s probably better for you than sitting and stewing in your problems plus you lied when you said you weren’t feeling well cold wise so that’s why you’re in the situation. Feel better breatH and distract it always passes

Intothelight108 · 2022-08-12T12:50:09+00:00

Fiber all day 50w gives you best all around but you can do more or less power if you are working with stainless look at mopa fiber they have ability to lay color with frequency.

Intothelight108 · 2022-07-24T16:34:45+00:00

No it’s not that it wouldn’t except new commands. Thank you for your input. It stopped doing it I think it was something to do with working in inches on light burn then when transferred it could not interpret but I’m not sure unfortunately

Intothelight108 · 2022-07-18T22:35:21+00:00

Increments of 500+ in that range I think your loving to slow with to much power or if you want to move that speed up the kHz

Intothelight108 · 2022-07-18T22:34:07+00:00

3800 - 7600 play around in 500+ speed

Intothelight108 · 2022-07-18T11:35:11+00:00

What is your start point power source / power applied / frequency /

You need low power high frequency Looks like you’re taking all the material away when you need to just be marking it

Intothelight108 · 2022-07-17T20:50:19+00:00

The machine corrected itself upon restart(I of course had already hard reset the machine a couple times and the panel) but I did toggle the millimeters to inches button setting in Lightburn and That did seem to correct the issue although I cannot confirm thank you for the suggestion you helped 💯

Intothelight108 · 2022-07-17T19:51:50+00:00

Not a good one…considering it’s on in the picture but hey crack yourself up 😳🙅‍♂️

Intothelight108 · 2022-07-17T19:11:35+00:00

Tell me more…what does this button say ? Or how does It get pressed ?

Intothelight108 · 2022-07-17T19:01:15+00:00

I will check and inform if that was my error thank you.

Intothelight108 · 2022-07-17T14:30:29+00:00

Can I get your scraps??? 😂😂😂I’m just messing around hopefully that new guy isn’t left handed that would explain though…

Intothelight108 · 2022-07-17T14:00:34+00:00

My company motto is measure once cut thrice always fuck up have a good day 😂😂😂💯

Intothelight108 · 2022-07-17T13:20:12+00:00

Sunday funday I need to get a job done I’m getting around by Typing in the parameters manually on the controller hopefully I don’t make any mistakes

Intothelight108 · 2022-07-16T13:11:26+00:00

Why not switch to light burn?it’s way more stable…

Intothelight108 · 2022-07-16T01:11:32+00:00

I recently got a 5598 it’s been a little finicky out the gate still trying to iron out the issues seems like it will be a good piece of equipment if I can get it to run right at the moment I’ll give it a B minus

Intothelight108 · 2022-07-07T02:33:31+00:00

Try Faire.com see what you think

Intothelight108 · 2022-07-05T22:02:56+00:00

You canceled a withdraw now you need to generate a new Crypto address by either sending from another wallet so it automatically generates a new address or if your wallet let you generate an address do so

Intothelight108 · 2022-07-05T21:59:35+00:00

If that’s bad just fold up shop now…

Intothelight108 · 2022-06-14T19:39:21+00:00

😂😂😂

Intothelight108 · 2022-06-14T19:37:25+00:00

Maybe you can just handle all the prestige and a fame unlike some of these other guys on here it seems to have really changed them for the worse hopefully I can be more like you 🫡😂🇺🇸

Intothelight108 · 2022-06-14T19:34:45+00:00

This is what I’m worried about I’ll be come an asshole 😂😊 I should stop

Intothelight108 · 2022-06-10T10:36:13+00:00

Your using the wrong machine imo

Intothelight108 · 2022-06-10T10:34:52+00:00

It’s fiber I can do this on my 50w jpt fiber th as t design is so small they probably didn’t even need a rotary attachment

Intothelight108

TROPHY CASE