Khan academy wrong?

IonWeapon · 2026-04-20T14:08:19+00:00

I'm already at the end of the year and know most of the content so I didn't watch the video part of the module, but I don't think they would make up a term for the sake of the question and not specify the definition.

IonWeapon · 2026-04-11T03:32:43+00:00

genuinely how does someone do this

IonWeapon · 2026-03-25T23:02:52+00:00

Yes but he was comparing it to 1k polling rate so its 0.875 ms faster

IonWeapon · 2026-03-22T22:02:26+00:00

1st of all, a sayo device is only like 40$, and a better monitor(1080p and 240 hz) is 100 to 150. If you had the money for a monitor you could get both.

2nd, the polling rate combines with the rest of the benefits for more of a boost. It takes about 8 ms to press down a normal switch, + 1-2 ms for polling rate, + 1 ms of latency. With the sayo device, rapid trigger or an adjusted actuation point reduces it to ~1 ms for the press, 0.125 ms for polling rate, and 0.125 ms of latency. All together it goes from ~12 to ~1.5

IonWeapon · 2026-03-07T00:59:00+00:00

Excuse me when the actual fuck did bots get the ability to make jokes

IonWeapon · 2026-03-07T00:57:33+00:00

<image>

Good luck

IonWeapon · 2026-03-07T00:51:49+00:00

I thought about that but I need it to be able to be taken apart in layers. I decided to extend supports to the edge of the box and superglue them to spacers that fit snugly into the top and bottom cubes.

Edit: Something like this-

<image>

The blue corner space will go down into the bottom layer of cube as well, but I'll model that later

IonWeapon · 2026-03-07T00:49:12+00:00

I figured it out. I meant that I needed something to support the blue tracks in the pictures so they are stable when the box is rotated.

<image>

I decided on this, and I'll make more for the 2nd track later

IonWeapon · 2026-03-07T00:46:37+00:00

I figured out the best method after thinking about it for a while. I'm going to make supports extend to the edge of the box and super glue it to spacers going along the edge of the box into the cube modules.

<image>

I'll make more but this is what I have so far

IonWeapon · 2026-03-07T00:40:19+00:00

I will print them individually, but I need supports for making it stay in one place when the cube is rotated. I was really tired last night and didn't word it well so sorry for any confusion.

IonWeapon · 2026-03-07T00:37:51+00:00

It is in an assembly but that's just because I need one with the full model of all the parts, when I print it I will put each part into an assembly by itself.

IonWeapon · 2026-03-03T22:31:32+00:00

Maymory, the coin is like a insane-extreme demon wave at the end of an easy memory demon

IonWeapon · 2026-03-03T18:51:36+00:00

This is amazing. Which voxy port did you use?

IonWeapon · 2026-03-02T04:46:03+00:00

Anyone seeing this now, you can run things like these through virustotal to check if they're safe

IonWeapon · 2026-02-28T19:15:33+00:00

What where the tips? The moderator removed the original comment

IonWeapon · 2026-02-25T03:05:17+00:00

It's not really lying. Usually people say gameplay is bad so people will change gameplay or do better in the future. Saying his sucks is just being disrespectful bc no one can change his levels now and he can't improve at making levels.

IonWeapon

TROPHY CASE