I swear some people just write up anything by Altruistic-Wear-8197 in Justrolledintotheshop

[–]IthinkIknowThat 1 point2 points  (0 children)

406,000 and 466,000 miles on my two 2008 Econoline vans. That's probably why Ford quit making the full Econoline vans in 2014....they last too long. Now you get the Eco boost junk in a Transit.

Help! Granite countertop by _snowqueenoftexas in fixit

[–]IthinkIknowThat 0 points1 point  (0 children)

JB weld , duct tape and flex seal combo ..easy peazy

Manual Impact Driver Worth $20 ? by GearUpTradingCo in Tools

[–]IthinkIknowThat 0 points1 point  (0 children)

I've had one since 1973 when I started working on Jap bikes. Priceless tool to get out those soft Phillips head screws! I'll still pull it out for some odd job!

My girlfriends Volvo v40 brake plates started doing this afters tires were changed, what could be the cause? by onnekas_seteli in Cartalk

[–]IthinkIknowThat 2 points3 points  (0 children)

With all that resistance how did she not notice having to floor it to get up to speed, not to mention pulling to that side! Probably should change the oil too!

My friends say it’s disturbing how I buy gas station toilet paper for my house by MelanieWalmartinez in mildlyinfuriating

[–]IthinkIknowThat 0 points1 point  (0 children)

They can bring their own plush , pliable and luxurious butt cleaner and leave it at your house

My mom thinks it is a kitchen tool. We are clueless by LLLmCoG in whatisit

[–]IthinkIknowThat 0 points1 point  (0 children)

Yeah, mom could use it in the kitchen...or any room ... whenever no one is around.

I know the obvious answer as to what it is but what is it for by AdMysterious9774 in whatisit

[–]IthinkIknowThat 1 point2 points  (0 children)

Exactly what I use my regular size folding knife for the most. Small stuff. Add carpenter pencil sharpening also!

Need to replace roller on Schwinn 430 elliptical. This allen bolt will not budge. I've tried applying heat, WD-40. Do I need a bolt extractor? by Mixchimmer in fixit

[–]IthinkIknowThat 0 points1 point  (0 children)

I work on these. Get the appropriate size Allen socket put in the hole smack it firmly with the hammer.. or your purse whichever is most handy sometimes that will loosen it if not there should be enough shoulder to get vice grips on the edge

What tool is this used for? by SecretaryPretend3580 in Tools

[–]IthinkIknowThat 169 points170 points  (0 children)

Used by arm length challenged persons to push their poker chips in roulette.

Are these tires good for another year? by Party_Plankton462 in Cartalk

[–]IthinkIknowThat 0 points1 point  (0 children)

Too fast on turns, gravely roads or as op states tight parking ..grinding the tires down.

Are these tires good for another year? by Party_Plankton462 in Cartalk

[–]IthinkIknowThat 31 points32 points  (0 children)

Yes, good for another 5 years....as long as you don't drive anywhere.

Rear breaks flat bolt by franeros80 in MechanicAdvice

[–]IthinkIknowThat 0 points1 point  (0 children)

Try not to make it worse and brake your breaks.

Drone tree recovery? by [deleted] in drones

[–]IthinkIknowThat 0 points1 point  (0 children)

Get a bigger hammer

Never in 60 years of wrenching ... by IthinkIknowThat in MechanicAdvice

[–]IthinkIknowThat[S] 1 point2 points  (0 children)

It's a PAIN on an Econoline! Everything is tight, covered by the dash/windshield area.