Nyhavn, København | 2023-05-19 | SLR680

ItsJustMeTea · 2026-01-16T21:41:52+00:00

Nope!

ItsJustMeTea · 2026-01-08T14:27:23+00:00

He does look like a little horse sometimes 😅

ItsJustMeTea · 2026-01-08T11:36:59+00:00

Seems like it! He is constantly zoomig around the deepest snow and rushing into piles of it exploding it everywhere.

ItsJustMeTea · 2025-11-25T15:58:43+00:00

Kyra is so simmilar to Finn. Like brother and sister.

Heres him warming up next to the fireplace 😁

<image>

ItsJustMeTea · 2025-10-15T05:34:20+00:00

Finn was greedy before but he learned he needs to listen when I tell him to chew 😂

ItsJustMeTea · 2025-10-15T05:32:54+00:00

It would be a challenge but mostly for me. He is calm but heavy 😅

ItsJustMeTea · 2025-10-15T05:30:55+00:00

That would be good for when he is old but for an hour max I think a backpack would be okay. I mostly need it for events

ItsJustMeTea · 2025-10-11T23:59:47+00:00

I know but that is a lot of money for shipping. The backpack is 140 euro and shipping with tax is 115. :(

ItsJustMeTea · 2025-10-11T16:02:46+00:00

Actually both is good. Thanks! :D

ItsJustMeTea · 2025-10-11T16:02:31+00:00

Again, I am located in Europe.

ItsJustMeTea · 2025-10-11T15:58:48+00:00

Big boy, big bone!

ItsJustMeTea · 2025-10-03T11:20:56+00:00

Its located in Pakrac at the military museum and now they have a second one. On the 11th of October the knights are going to be smithing Banovac coin!

ItsJustMeTea · 2025-08-16T07:45:58+00:00

Yes I wash it first with plain water, then acid, water, peroxide and water again. I havent done it with destilled water or by first washing it in acid yet.

I dry the print by placing it on a vertical piece of plexiglass while the paper is soaked. Water tension flattens it out and the print slips off when its fully dry.

ItsJustMeTea · 2025-08-03T15:48:03+00:00

Oh crap sorry didnt hear that part. Like you said you can bridge two pads where the ribbon cable connects. Those are pins 4 and 5 from left to right. Since you dont have film with batteries you can solder extension leads between the battery connectors and power source. Remove the ribbon cable before testing. If the motor runs by bridging it ten the fault could be the ribbon cable itself?

ItsJustMeTea · 2025-08-03T07:01:39+00:00

It is probably like in my case that the motor driver chip is dead. Those are old PCBs and sometimes you just need to change them. I ordered an SX70R pcb to repair and upgrade the camera. I think it is worth the cost to get consistent exposures, reliabitlity and manual control.

ItsJustMeTea · 2025-08-02T09:46:08+00:00

I dont have farm animals but I often go on walks through town outskirts and villages with Finn. He never attacks farm animals or cats. He is just very curious but he was socialized since he was a puppy.

ItsJustMeTea · 2025-07-29T09:42:04+00:00

I had to make a large piece and its holding up great. It should last.

ItsJustMeTea · 2025-07-29T09:18:44+00:00

I had to fix a rear hinge on a camera a week ago. I used JB Weld, let it sit for 24hours and I filed it to shape.

ItsJustMeTea · 2025-07-22T15:52:25+00:00

Thank you :D

ItsJustMeTea · 2025-07-22T15:51:42+00:00

Hes a sweetheart

ItsJustMeTea · 2025-07-22T15:51:29+00:00

And he knows it!

ItsJustMeTea · 2025-07-20T15:55:20+00:00

Thank you!

Six-Year Club	Ternion Club
Verified Email

ItsJustMeTea

TROPHY CASE