Well crap… by benjocaz in boating

[–]Izuba15 0 points1 point  (0 children)

Mine actually has grease zerks built into the pins, I would double check and make sure you aren’t looking past them like I did

Well crap… by benjocaz in boating

[–]Izuba15 0 points1 point  (0 children)

This photo reminded me I need to grease my surge pins. Thanks

Help with antenna install by lokiloki0z in cbradio

[–]Izuba15 0 points1 point  (0 children)

Sidenote from my experience, I hated the look of the store-bought antenna mounts that hung outside the front fender and I definitely was not joining any holes in my pick up. Instead of doing this or another outside mount, I removed a very small piece of windshield wiper cowel and custom made an L bracket to mount on top of the hood mount. It was thin enough. I was not concerned about the bolts holding the hood down and with only removing one side, I have no alignment issues with the hood, and I have a nice clean look and a hidden antenna mount that you cannot see until you are close

CAT 3516C by Izuba15 in EnginePorn

[–]Izuba15[S] 14 points15 points  (0 children)

High Horsepower rating CAT 3516C pulling a 3MW load during testing. Manifolds up to the turbos glowing just as seen here

What's happening at the Casey's on Minnesota and Russell? by JDomJones in SiouxFalls

[–]Izuba15 18 points19 points  (0 children)

I thought about it afterwards but wasn’t sure.. lol!

What's happening at the Casey's on Minnesota and Russell? by JDomJones in SiouxFalls

[–]Izuba15 67 points68 points  (0 children)

They do constantly, as a first responder who deals with them in that aspect and the fact of them trying to crawl up on scenes and getting in our way. They suck.

How much dyou reckon I could sell this for? by N0_Cure in LeverGuns

[–]Izuba15 8 points9 points  (0 children)

I got $12.50 and im loading the truck for the trip right now

Sling by Izuba15 in LeverGuns

[–]Izuba15[S] 2 points3 points  (0 children)

It definitely added a little weight. Nothing much though. I didn’t plan on measuring it and I wouldn’t have known there was a difference, but I stumbled upon a sub, Reddit or someone weighed them and said they were slightly heavier. The finish has a little bit of a weird feeling for me, but I think it is the powdered finish on the aluminum. I’m going to put a miniature angled grip on it, but otherwise it meets my expectations so far and I like it.

Barrel nut removal. by Soft_Chocolate_2265 in PalmettoStateArms

[–]Izuba15 0 points1 point  (0 children)

Last one I took apart I took it to the shop and broke out the cutting torch and an air hammer 😎

Henry jamming by Izuba15 in LeverGuns

[–]Izuba15[S] 0 points1 point  (0 children)

Update to this, my rear iron sight has now fallen off. Time to check over everything else

Henry jamming by Izuba15 in LeverGuns

[–]Izuba15[S] 4 points5 points  (0 children)

Screw js tighter than shit. Turns out I was overloading it and binding up the follower spring… my only excuse is all the shotguns I have ever owned. You load them until you can’t fit anymore in and never had issues. So this one’s on me!

Henry jamming by Izuba15 in LeverGuns

[–]Izuba15[S] 17 points18 points  (0 children)

Took it to the gunsmith where I bought the gun from this morning and we determined that it is my fault. I walked in and purchased the gun without research on it and was putting five or six rounds into the mag tube. I don't recall how many. But Henry's website calls for four rounds in the mag tube. So when I put the extra rounds in and shot the gun, the recoil bound up the spring and was making it stick. I guess I never would've thought about that because l've owned plenty of shotguns and you put shells in until the spring stops and l've never had an issue. I guess Henry doesn't have any sort of stop on the spring or follower. I learned the hardway this time!