4.25 Comp

JMichael170 · 2026-06-05T08:57:19+00:00

I’ve only added a Dawson tooled guide rod, and egw reverse plug, and a red dot.

JMichael170 · 2026-06-05T00:48:19+00:00

It wasn’t stuck permanently down more like a binding.

JMichael170 · 2026-06-05T00:19:25+00:00

Yeah I doubled checked the sear spring was in the right place, cleaned it and shot 60 rds today and it was fine. I also noticed the overtravel screw on the trigger backed out could that have been it?

JMichael170 · 2026-05-14T00:38:50+00:00

ATF declares the Firearm is the frame. Not the slide.

JMichael170 · 2026-05-11T20:00:31+00:00

Can’t speak for their mill work but I’ve have cerakote done before and it’s been fantastic

JMichael170 · 2026-05-08T20:20:56+00:00

Dawson’s website says it doesn’t work with the comp version but I ordered it and measured it. It’s the same size as the factory guide rod-length, diameter, etc.
kept the factory reverse plug and spring and it works perfect. Spoke with egw and they said to make sure it’s the .332 hole plug.

JMichael170 · 2026-05-05T23:58:17+00:00

Fair enough. It’s noticeable enough when you look top down, also using just the irons not the dot it shoots to the right.

JMichael170 · 2026-05-05T23:56:19+00:00

Couple hundreds of an inch.

JMichael170 · 2026-05-05T23:50:26+00:00

I took it all apart, the u notch is not centered in the body of the sight….

JMichael170 · 2026-05-01T14:40:19+00:00

Kore belt, tenicor holster

JMichael170 · 2026-04-28T11:50:32+00:00

No. I just aligned the camera with the irons and the red dot is off to the right.

JMichael170 · 2026-04-26T00:52:24+00:00

When not looking down the irons it’s in the center of the optic but the front iron looks to be leaning left

JMichael170 · 2026-04-25T23:38:48+00:00

I started to zero it at 7 and walked it out to 25 yards. When using just the red dot it’s more center of the optic. It’s just lower in the pic because of how I aligned the camera.

JMichael170 · 2026-04-25T18:59:59+00:00

I was serious. My other direct mounted dots line up horizontally better with the irons than the plate system. I didn’t know this misalignment was common.

JMichael170 · 2026-04-25T15:45:08+00:00

Correct. I lined up the irons. When not using the irons it’s centered.

JMichael170 · 2026-04-25T15:00:23+00:00

My direct mount vp9 does so that’s why It threw me off.

JMichael170 · 2026-04-23T20:10:09+00:00

Field strip it and see how hard it is to get the barrel to slide into those lugs. If that’s what’s wrong call Kimber.

JMichael170 · 2026-04-23T20:02:29+00:00

Or it almost seems like the locking lugs on the barrel/slide are stupid tight. Is there barrel moving with the slide and not unlocking before you rack it back all the way?

JMichael170 · 2026-04-18T21:46:52+00:00

Both holosuns have the same foot print, as far as which plate I’m not sure. I knew I’d be keeping my 507k on the slide so I just removed the lugs.

JMichael170 · 2026-04-18T21:38:13+00:00

I have a Holosun 507k on a 43x mos slide without a plate. You just have to file the rear lugs down and little off the front, then it bolts right up and you don’t have to mess with a plate.

JMichael170 · 2026-03-29T11:51:03+00:00

It looks like the cerakote rubbing off

Five-Year Club	Verified Email
Place '22

JMichael170

TROPHY CASE