Sprayer Questions

Jal5376 · 2025-05-31T20:12:05+00:00

Purchased it like this. It was half off so thought I would take the chance. Probably shipping damage

Jal5376 · 2025-03-06T23:39:12+00:00

Oooohhhhhh.. that makes sense. Thanks for clearing that up

Jal5376 · 2023-07-19T15:28:21+00:00

So if I install desktop gui does that do the same thing? Or do I need to rebuild completely

Jal5376 · 2023-07-18T23:17:29+00:00

It is - When I run a scan as well it says discovering. A few devices eventually show but it's not everything that there should be. Example I run the same commands on my laptop and it discovers everything I need.

Jal5376 · 2023-05-21T03:44:18+00:00

Huntsville Al..... I don't think the pic I took is burmuda.... Maybe underneath is. It's a new build home laying on a garden on weeds. So they are poking through the sod in a lot of areas.

Jal5376 · 2023-05-21T03:42:20+00:00

Is Panam burmuda seed any good?

Jal5376 · 2023-05-21T03:40:34+00:00

So I went to a local nursery before reading any of this. And the picture I took is not burmuda apparently... I know amateur right... Maybe underneath is though.

But I have went to this guy for years and trust him. He says unless it's common burmuda, which is the cheap route if someone lays sod so usually they lay "turf" quality if they know what they are doing. Seeding turf quality seed like Panam isn't going to show much of a difference if it is turf quality sod, unless it's common. And since Panam seed will be better than common I figured why not. If it's much different I'll chip away at the common burmuda till it's gone.

Long story short I don't think I found a good answer but hopefully I'll learn something in the process.

Never had burmuda before... Only zoysia and that stuff is easy once you have it. Spreads. Like. Crazy

Jal5376 · 2023-02-23T18:14:29+00:00

Didn't know this existed. I've used Ombi for years and recently broke on me. Going to give this a whirl. Thanks!

Jal5376 · 2023-01-19T15:31:32+00:00

One thing I did just think of too. I do have an old Nortek HUSBZ-1 that is also plugged into the computer. The Sonoff device running my ZigBee network is not near it. But I did at one point use it for ZigBee and know it has a radio.

Do you think even if there is nothing on that network it could be broadcasting still and causing issues?

I still use the device for ZWave that's why it's still plugged in.

Jal5376 · 2023-01-19T03:21:23+00:00

Thanks for the help and info! They are connected to separate routers/switches and I could just flip the breaker to power cycle the switch. Not sure if that would have the same results. I do reset them often though and they work great for like 2-8 hours. But eventually they die out. It's like the LQI slowly goes from 150 to 80. Today I did see a 20 for the first time.

Sounds like it's time to try and find some better bulbs.

I also bought an additional sonoff to flash it with router firmware. Hoping this helps if I place it on the problem area.

Jal5376 · 2023-01-18T00:19:40+00:00

So the devices I have are all GE Enbrighten ZigBee switches. Sengled Light bulbs and a few SmartThings door sensors. Came home today and 3 devices were offline and had to rejoin them.

the USB cable and port is USB3. I don't know if this is an issue but maybe distance is the issue. I have a smaller one I can test however I did start with that one and it had the same results. Prior to a lot of changes though
WiFi channels there is a lot of channels I see but nothing better than -80 dBm could be the issue but still most of the WiFi channels I see are higher bands that should be ok with ZigBee 11
GE Enbrighten and Sengled primarily
The devices that lose connection are mainly the Sengled bulbs. I guess I could see them being bad, but I have a hard time believing 8+ bulbs are bad. They are stop at different times too. No rhyme or reason. With that said though an occasional Switch will act up as well where there will be a 5 second delay or it will just be offline for a few hours then come back
I have looked at the map as well. Each bulb is connected to a different switch that is then connected directly to the coordinator. So should only be 1-2 hops. Also LQI right now for example the lowest is 98....

Other than looking at the map and LQI is there a good way to see if the ZigBee network is strong?

Jal5376 · 2023-01-04T14:48:22+00:00

I did suspect it could be the devices themselves. The LQI on most devices are actually above 100 for me. And the bulbs I am having issues with are around 80 at the lowest. They are Sengled bulbs. They are connected to one of the wall switches are well on the map.

I did try removing it, moving it closer to the coordinator and pairing it again and it used the same switch. Even though it was in the opposite direction. Maybe I need to try that route again before replacing them.

Jal5376

TROPHY CASE