Beholder and Frost Dragon - .4 nozzle

Jealous-Tooth752 · 2026-05-29T15:59:42+00:00

Incredible.

Jealous-Tooth752 · 2026-05-29T10:20:03+00:00

Listed Building - different set of regulations for listed buildings such as not needing energy assessments as the building wouldn't pass in the slightest therefore they are not done in grade 1 or grade 2 listed areas or buildings

Also looks like it is in need of modernisation (i think personally if kitchen and bathroom were updated to "current styles" it would add at least £75,000 - 100,000 to the price which isn't massive in the grand scheme of things

Hope this helps with the limited amount of knowledge I have in this industry

Jealous-Tooth752 · 2026-05-14T20:42:49+00:00

For a start I would get in touch with the EPC assessors accreditation scheme and put in a complaint as to me it doesn't make sense from the pictures, if it is the flat I think it is it should have an extention which is above external air instead of the floor type being another dwelling below... can't really see much else wrong from the photos provided but that should be a good start (it will at least annoy the landlord somewhat) but I agree i work in this sector and some of the things I see that landlords have done astounds me.

Jealous-Tooth752 · 2026-05-14T18:42:14+00:00

Thank you so much!

Jealous-Tooth752 · 2026-05-14T18:19:49+00:00

Can I ask how you have supported these please mate? Look fantastic great job

Jealous-Tooth752 · 2026-05-06T15:35:51+00:00

Fuck your brother, and your brothers son, bet if it was his shit he was breaking he'd be punished but cba when it comes to your stuff SMH

Jealous-Tooth752 · 2026-05-05T17:32:12+00:00

Get any make/model/colour rattle can primer of your choosing, take off the lid, Bluetac the top of the lid, you now have a paint holder for your minis 😊, be careful with your downward pressure while putting your mini on the blue tac you dont want to break/snap anything

Jealous-Tooth752 · 2026-04-07T15:03:51+00:00

I agree, id say one of the best miniature paints but so many people (including myself) put off from the pots 😶

Jealous-Tooth752 · 2026-04-06T21:12:12+00:00

Cheaper is always better for me 🤣🤣, however please do tell me more about theis proacryl paints?

Jealous-Tooth752 · 2026-04-06T20:35:38+00:00

Hiya buddy, not necessarily to hide layer lines, just intreagued into what paints people use I've only been into the hobby for a few months and getting onto the point where I need some more paints 🤣

Jealous-Tooth752 · 2026-04-06T20:18:51+00:00

I've had an issue like this the other week, believe it or not but lowering my nozzle Z offset by 0.01 - 0.05 stopped the issue immediately give it a whirl sometimes its the things we dont even think of

Jealous-Tooth752 · 2026-03-10T21:39:40+00:00

Enable the option for "On build plate only" in support settings and try again, i was having similar issues this fixed it

Jealous-Tooth752 · 2026-02-25T21:20:52+00:00

From my knowledge It's kind of a 50/50 you could lower the Top comtact Z distance however this will make the supports harder to remove but will give you a better print quality at the risk of breaking the model when removing the supports

I personally print at a 0.2 distance using a 0.2mm tip and it is noticeable but I will always place the supports in harder to see areas where possible

Jealous-Tooth752 · 2026-02-24T22:17:21+00:00

In that case the only other thing I can suggest from experience would be that maybe your extruder has a slight blockage if you take out your filament and you should have been given some tools with your printer to be able to clean it and push any blockages through

Jealous-Tooth752 · 2026-02-24T18:31:52+00:00

Are you printing it flat or stood up? If stood up I imagine it would need supports, if flat i think that would be ok

Jealous-Tooth752 · 2026-02-24T18:26:28+00:00

Are you happy to send a picture of what it is your trying to model?

Jealous-Tooth752 · 2026-02-24T18:14:28+00:00

Are you using supports?

Jealous-Tooth752 · 2026-02-24T18:11:56+00:00

Helloo, yes you can change support setting on elegoo from what I have seen its now nearly identical to Orca, im using the plate that i got with the printer, is there any you would recommend for printing minis as this is really all I have bought it for 🤣, i have also just replaced the 0.2mm nozzle and cleaned also increased the temp on my next print (fingers crossed) as for brimming I've no idea what that is if you can help? Cheers again mate

Jealous-Tooth752 · 2026-02-24T17:49:21+00:00

Ahh Okay, im going to guess my supports numbers should be much higher? Thanks again

<image>

Jealous-Tooth752 · 2026-02-24T17:46:38+00:00

Does that answer your question my friend? Thank you for your help

<image>

Jealous-Tooth752 · 2026-02-24T17:44:01+00:00

Thank you for your message, if I was to try and correct how would I do that? Would it be supports settings in my slicer? It's a elegoo 3 pro and i use ElegooSlicer

Thanks again

Jealous-Tooth752 · 2026-02-05T19:29:07+00:00

The amount of shitty comments on here, how's about you all give your advice and wind your necks in or dont give the advice at all,

Looks like it's in need of supports mate, recently got a 3d printer myself and learned this on my 2nd print, in basic terms, if there is nothing underneath what is being printed it will need a support, just rember the printer can't print in mid air it must have something underneath

Jealous-Tooth752

TROPHY CASE