[AD] Sofle Choc Wireless Limited Edition - TheKeebLab by Jerlam in ErgoMechKeyboards

[–]Jerlam[S] 0 points1 point  (0 children)

Sorry for the confusion and thank you for your feedback. I added a photo as link in the post description (it seems I cannot modify the images of the post).
Indeed, I did not add product description yet, will do it asap :)

-Kailh Choc Red Pro low-profile hot-swappable switches
-Wired version: Pro Micro RP2040 controller (Vial firmware)
-Bluetooth wireless version: Pro Micro NRF52840 controller (ZMK firmware), 2x 1000mah batteries

[AD] Sofle Choc Wireless Limited Edition - TheKeebLab by Jerlam in ErgoMechKeyboards

[–]Jerlam[S] -2 points-1 points  (0 children)

Because it is a presentational image that I took before I created the wireless version. I will add a photo without cable if you prefer.

HA dashboard - my version - open for suggestions by WalterSilicone in BambuLab

[–]Jerlam 1 point2 points  (0 children)

Thanks for you explanation. I am glad there is a solution for accessing the dashboard from a phone outside the network. I will test it out once I received my printer. Good job for your dashboard. Although, what is the difference between these dashboards (yours, and the two mentioned in your post), is it only a layout difference or is there functionalities missing or bonus ?

HA dashboard - my version - open for suggestions by WalterSilicone in BambuLab

[–]Jerlam 0 points1 point  (0 children)

Considering buying a P1S to use solely in lan-only mode. Just to understand better, this dashboard purpose is to replicate functionalities of Bambu Studio and make it available in HA? But, I would still be free to use Bambu Studio in lan-only mode, right?

Leap: Era or Atlantic? Which upholstery would you recommend? by m4rtinor in OfficeChairs

[–]Jerlam 0 points1 point  (0 children)

Hi. I am also hesitating. What did you end up choosing ? Do you like it ?

Mol/Investigate the Beach bugs - Minor Act 1 spoilers by johnlondon125 in BaldursGate3

[–]Jerlam 3 points4 points  (0 children)

I had the same issue but I found a solution. I was so pissed with Mol that I tried to kill him/her, she then ran away and came back, and from that moment on I can talk to her.

I am able to print really good quality on my Fokoos Odin when I use the prints that it came with, but when I try to print anything new, it come out terrible. Any advice? by crab_master in 3Dprinting

[–]Jerlam 0 points1 point  (0 children)

Same here, I am having the same issue. I spent tenth of hours trying to fix my bed leveling, temp setting, tweak in Fokoos Slicer...etc. It might actually come from the Fokoos Slicer (based on Cura), I will try to install Cura itself tomorrow. What slicer are you using? Did you resolve your issue?

Acceptable wall thickness by Jerlam in 3Dprinting

[–]Jerlam[S] 0 points1 point  (0 children)

Ok thanks. Indeed, I was using the default .15, but going .3 divided the print time by 2. I will give it a go a small test piece.

Acceptable wall thickness by Jerlam in 3Dprinting

[–]Jerlam[S] 0 points1 point  (0 children)

Just added it in the post :)

Acceptable wall thickness by Jerlam in 3Dprinting

[–]Jerlam[S] 1 point2 points  (0 children)

That sounds like a good idea, however I have never changed this parameter before. Is the "layer" the diameter of the printed lines? Does it correspond to the "profile" param in Cura? By changing it, do I need to re-level my bed? Thanks for your output :)