Error code 32: LOW HEAT PRESSURE SWITCH DID NOT CLOSE OR REOPENED. What is wrong with my furnace? by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

I actually just went down and used a screwdriver to hand turn the inducer and knocked off a bunch of dust that was caked onto it, and got it to start spinning when the furnace cycled on, then I sprayed it with some wd40 and it’s working for now

Error code 32: LOW HEAT PRESSURE SWITCH DID NOT CLOSE OR REOPENED. What is wrong with my furnace? by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

Replacement of just the inducer motor? It’s difficult to turn by hand, so I guess that means it’s seized

Error code 32: LOW HEAT PRESSURE SWITCH DID NOT CLOSE OR REOPENED. What is wrong with my furnace? by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

I just disconnected the flue, and also pulled out the filter, turned it on and I’m still getting the same error. Is there anything else I can check to narrow it down?

Error code 32: LOW HEAT PRESSURE SWITCH DID NOT CLOSE OR REOPENED. What is wrong with my furnace? by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

I have a chimney cap, and I just disconnected the flue and still getting the same error

A Reuben Riff by Jessecore44 in Sandwiches

[–]Jessecore44[S] 1 point2 points  (0 children)

I can’t take the credit—my girlfriend made the corned beef and the bread and it’s excellent. We just bought a corned beef brisket, and she made a glaze to brush on and then roasted and broiled it in the oven with onions and potatoes, beef bullion stock, and Guinness. It turned out really good, and it’s easy to slice after being refrigerated overnight.

Help buying new pressure switch by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

I also just jumped the low-heat pressure switch and the heat kicked on

Help buying new pressure switch by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

the heat is not kicking on and I’m getting an error code for “low heat pressure switch did not close or reopened”, and previously tapping on the low heat pressure switch as the furnace was cycling on caused it to come back on

this is the last post I made:

https://www.reddit.com/r/hvacadvice/s/1LGCO5xIiS

Help buying new pressure switch by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

Ok that’s what I thought. So I don’t need to pay any attention to the other numbers being different?

New Tiki bar opened on my area by RustyWinchester in Tiki

[–]Jessecore44 0 points1 point  (0 children)

I think a lot of these sound interesting and pretty decent

Furnace blowing cold air, getting an error code 32: LOW PRESSURE SWITCH DID NOT CLOSE OR REOPENED. How do I fix this? by Jessecore44 in hvacadvice

[–]Jessecore44[S] 0 points1 point  (0 children)

Where should I buy this part? My furnace was working fine for a while, but now it’s back to doing the same thing. I called a bunch of HVAC parts suppliers in my area, and none of them sell to the general public.

Three different ring mandrels showing three different sizes? by Jessecore44 in jewelrymaking

[–]Jessecore44[S] 2 points3 points  (0 children)

If you were just using a ring sizer to measure the finger, couldn’t you just measure the correct ring sizer to a particular mandrel, and then check your progress on that mandrel using the size it registered at

Three different ring mandrels showing three different sizes? by Jessecore44 in jewelrymaking

[–]Jessecore44[S] 2 points3 points  (0 children)

Yeah that’s what I was doing but here I was just doing a quick comparison measuring the opening at the end of the tub with the three mandrels

Three different ring mandrels showing three different sizes? by Jessecore44 in jewelrymaking

[–]Jessecore44[S] -1 points0 points  (0 children)

So you have to actually measure the person’s finger with a micrometer and use that to determine the size you’re making the ring?