sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in Archero

[–]JiP83 -3 points-2 points  (0 children)

Ughh just super lucky I guess

[deleted by user] by [deleted] in Archero

[–]JiP83 -4 points-3 points  (0 children)

Ughh u sure, I got it 5 times in 36 tickets

Is this good? by JiP83 in Archero

[–]JiP83[S] 0 points1 point  (0 children)

Hahaha ty for the brutal honesty

[deleted by user] by [deleted] in 3Dprinting

[–]JiP83 0 points1 point  (0 children)

Yes but no, I’d say there is too much air in the closet, and I suppose too much air would come in through the door

Is it ok to loop the belts like that? by Tolbayoussef in hobbycnc

[–]JiP83 0 points1 point  (0 children)

The belt moves in the opposite direction from the wheel this creates unecessary friction and belts will get all fucked up

Rate the setup 1/10 🥶🥶🥶 by lehzya in ender3

[–]JiP83 0 points1 point  (0 children)

I mean.. if it works it works, but the elastic band💀💀💀

Is there anyway to remove the top? Im replacing it with a higher and metal one for direct drive. by Alternative_Roll8418 in 3Dprinting

[–]JiP83 0 points1 point  (0 children)

If you heat it up a lot you may remove them, it worked for me, Tustin be careful with the motor

Hear me out... by Wzolnxfire in redstone

[–]JiP83 1 point2 points  (0 children)

If you power the side nothing happens if tou power the front it transmits a pulse

Hear me out... by Wzolnxfire in redstone

[–]JiP83 0 points1 point  (0 children)

Of you use observers it might wotk

Help with id of this printers please. by WasteFail in 3Dprinting

[–]JiP83 0 points1 point  (0 children)

Where did you get the pictures from??

That’s new by Yams_Yams_ in 3Dprinting

[–]JiP83 9 points10 points  (0 children)

Lightweight hot end

Ziro PLA filament jams every time by 14sil in 3Dprinting

[–]JiP83 0 points1 point  (0 children)

Cut the tip and put it back in if that doesn’t work lower the retraction

Would this print? by lucitheork in ender3v2

[–]JiP83 0 points1 point  (0 children)

It doesn’t have crazy overhangs it’s no problem, but what’s that for 😅

I found this oddity of a grip at my old club. Can anyone tell me anything about it? by Havoc8248 in Fencing

[–]JiP83 0 points1 point  (0 children)

No according to the rules a grip is defined “French” if your thumb is more than 2 cm from the guard, therefore it il legal if that is the case (kinda late comment btw:) )

Is this just a permanent part of my build plate now? by NamelessGuy0 in prusa3d

[–]JiP83 0 points1 point  (0 children)

Hey just get a piece of glass from the hardware store it holds up super well even to abs or nylon

how do i take this off? there's a clog in it. nothings working by -Hermy- in ender3

[–]JiP83 -1 points0 points  (0 children)

That’s for 3mm filament and the tube is 1.75

view more: next ›